Download VCE Vblock System Deployment and Implementation – Virtualization.210-015.VCEplus.2024-08-04.47q.vcex

Vendor: VCE
Exam Code: 210-015
Exam Name: VCE Vblock System Deployment and Implementation – Virtualization
Date: Aug 04, 2024
File Size: 110 KB
Download Exam

How to open VCEX files?

Files with VCEX extension can be opened by ProfExam Simulator.

Download
ProfExam Simulator

Purchase
Coupon: EXAMFILESCOM

Discount: 20%

ProfExam Simulator ProfExam Simulator ProfExam Simulator ProfExam Simulator ProfExam Simulator

Demo Questions

Question 1
You are working with a customer to enable VMware Fault Tolerance on a number of virtual machines and you encounter the error shown below on one of them.
The Fault Tolerance configuration of the entity SalesVM has an issue Fault Tolerance not supported by host hardware What is the cause for this error?
  1. Fault Tolerance requires that the hosts for the primary and secondary virtual machines use the same type of CPU.
  2. This virtual machine is on a host that is not in a vSphere HA cluster or it has had vSphere HA disabled.
  3. Fault Tolerance is only supported on specific processors and BIOS settings with Hardware Virtualization enabled.
  4. The virtual machine is running VMI kernel and is paravirtualized.
Correct answer: C
Question 2
Which three configurable settings are available directly through the DCUI? (Choose three.)
  1. IP address
  2. date
  3. firewall ports
  4. hostname
  5. VLAN ID
Correct answer: ADE
Question 3
A customer has recently acquired some new Cisco UCS B440 M3 blades to install in their existing Vblock System. You are asked to add these new blades to the existing vSphere cluster and to ensure full compatibility with the existing environment.
Which action must you perform?
  1. Enable EVC mode with a feature set of the existing CPU level to ensure compatibility with the new blades.
  2. Enable EVC mode with a feature set of the newer CPU level to ensure compatibility with the existing blades.
  3. Disable VMware HA prior to adding the new blades to the cluster.
  4. Modify the limit CPUID value advanced setting on the existing blades to ensure compatibility with the new blades.
Correct answer: A
Question 4
You ordered additional SAS drives to increase the capacity of your Vblock System 300.
What is the VCE recommended RAID configuration?
  1. RAID1 (4+4)
  2. RAID5 (4+1)
  3. RAID6 (6+2)
  4. RAID5 (7+1)
Correct answer: B
Question 5
What is the proper sequence when upgrading the Cisco Nexus 1000V switch module?
  1. 1. Upload new VEM code to bootflash. 
    2. Install new Cisco Nexus 1000V bin.
    3. Verify the upgrade using the show install all status command.
  2. 1. Upload new VSM code to bootflash. 
    2. Install new Cisco Nexus 1000V bin.
    3. Verify the upgrade using the show version command.
  3. 1. Upload the new VSM code to a USB drive. 
    2. Install new Cisco Nexus 1000V bin.
    3. Verify the upgrade using the show install all status command.
  4. 1. Upload the new VEM code to a USB drive. 
    2. Install a new Cisco Nexus 1000V bin.
    3. Verify the upgrade using the show version command.
Correct answer: A
Question 6
During the deployment of a Vblock System 320, the customer stresses the importance of network security and states that they would like to have a VM scan and capture all packets on the virtual switch to which it is connected.
Which security policy should you set?
  1. jumbo frame
  2. MAC address change
  3. promiscuous
  4. port scan
Correct answer: C
Question 7
What is the standard size of an ESXi boot LUN for a Vblock System 300?
  1. 5 gigabytes
  2. 15 gigabytes
  3. 20 gigabytes
  4. 50 gigabytes
Correct answer: C
Question 8
You are asked to restore a virtual machine from a SAN array snapshot.
Which two actions must you perform to present the LUN to the ESXi host to make the data available? (Choose two.)
  1. Force mount the copy of the LUN if you are sure the original is not in use.
  2. Resignature the copy of the LUN if the original is still in use.
  3. Restore the LUN to the ESXi host.
  4. Add the copy of the LUN to the ESXi host using the format option.
Correct answer: AB
Question 9
You are adding an NFS volume to an ESXi host.
Which three steps are required? (Choose three.)
  1. Create a vmkernel interface on the ESXi host.
  2. Create a network label to identify the connection.
  3. Choose the NFS folder name in the format volmountsdatastore1.
  4. Choose Network File System as the storage type.
  5. Assign a VSAN to the vmkernel interface.
Correct answer: ACD
Question 10
  
After scanning a host for compliance in VMware Update Manager you receive the message shown in the exhibit.
What is the reason for the message?
  1. The VEM VIB in the ESXi 5.x upgrade image is not compatible with the version of the VSM.
  2. A VEM VIB is not available in the ESXi 5.x upgrade image.
  3. The host and the image do not contain VEM VIBs, but the host is still listed in vCenter Server as managed by Cisco Nexus 1000V.
  4. There was a problem with determining compatibility between the VEM VIB in the ESXi 5.x upgrade image and the VSM.
Correct answer: B
CONNECT US
HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset

HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen

ProfExam
ProfExam at a 20% markdown

You have the opportunity to purchase ProfExam at a 20% reduced price

Get Now!