Download Applying HP FlexNetwork Fundamentals.HP0-Y52.PracticeTest.2018-01-15.116q.vcex

Vendor: HP
Exam Code: HP0-Y52
Exam Name: Applying HP FlexNetwork Fundamentals
Date: Jan 15, 2018
File Size: 5 MB
Download Exam

How to open VCEX files?

Files with VCEX extension can be opened by ProfExam Simulator.

Download
ProfExam Simulator

Purchase
Coupon: EXAMFILESCOM

Discount: 20%

ProfExam Simulator ProfExam Simulator ProfExam Simulator ProfExam Simulator ProfExam Simulator

Demo Questions

Question 1
An HP Comware switch should send messages to an SNMP server when various events occur. What is one step in the configuration of this feature?
  1. Enable SSH on the switch, and create a user account to match settings on the SNMP server.
  2. Set the SNMPv2 read-write community string to match the string on the SNMP server.
  3. Enable logging to the console globally.
  4. Specify an SNMP trap server with the SNMP server IP address and community string.
Correct answer: D
Question 2
Exhibit1. 
   
Exhibit 2 
   
A network administrator wants to create a backup IP route to 10.1.20.0/24 on Switch-1. The backup route should use Link 2, and it should only be used if Link 1 is down. What is the correct setup to accomplish this?
  1. an IP route through 10.0.2.2 with administrative distance 1
  2. an IP route through 10.1.20.1 with administrative distance 1
  3. an IP route through 10.0.2.2 with administrative distance 10
  4. an IP route through 10.1.20.1 with administrative distance 10
Correct answer: D
Question 3
Refer to the exhibit. 
   
This switch currently assigns all VLANs to Multiple Spanning Tree Protocol (MSTP) instance 0 or the Internal Spanning Tree (IST). Which statement correctly describes interface 21?
  1. The interface is down at Layer 2; it is not available for sending or receiving any traffic.
  2. The interface is an edge port but has received Bridge Protocol Data Units (BPDUs), so it is disabled.
  3. The interface does not forward or accept data traffic, but it is ready to start forwarding if interface 19 fails.
  4. The interface does not support spanning tree; it is possible that it will introduce a loop in the network.
Correct answer: B
Question 4
Refer to the Exhibit. 
   
Originally, all four switches had the same region configuration. VLAN 14 was added to Switch_D and then mapped to instance 2. How does this affect the Multiple Spanning Tree Protocol (MSTP) topology?
  1. Load sharing is lost; one of the uplinks is blocked for all traffic on Switch_D.
  2. All connectivity is lost; both uplinks are blocked on Switch_D.
  3. A Layer 2 loop exists and will cause sporadic connectivity issues.
  4. Load sharing is lost; one of the uplinks is blocked for all traffic on Switch_C and Switch_D.
Correct answer: B
Question 5
Refer to the Exhibit. 
   
A network administrator has configured an HP Comware switch to act as the DHCP server for VLAN 12, but the switch is not responding to clients’ DHCPDISCOVER messages. Based on the exhibit, what is the problem with the DHCP configuration?
  1. DHCP is not enabled globally on the switch.
  2. DHCP relay is not enabled on VLAN 12.
  3. DHCP server is not enabled on VLAN 12.
  4. DHCP server ping timeout setting is set too high.
Correct answer: A
Question 6
Refer to the Exhibit. 
    
Examine the output from the Comware command shown in the exhibit. Based on the flag of ACDEF, what is the status of the aggregated link?
  1. Static LACP link aggregation is configured, and the aggregated link is operational with load sharing not being performed.
  2. Static link aggregation is configured, and the aggregated link is operational with load sharing being performed.
  3. Static LACP link aggregation is configured, and the aggregated link is operational with load sharing being performed.
  4. Static link aggregation is configured, and the aggregated link is operational with load sharing not being performed.
Correct answer: B
Question 7
A network administrator enters this command on an HP Comware switch:
<Comware> save 
In interactive mode, the administrator is prompted to save to a file named config.cfg and confirms the save. What is the effect of these actions?
  1. The current configuration is saved to config.cfg on a TFTP server but is not used for the startup-config.
  2. The startup-config, rather than the correct configuration, is saved to config.cfg on a TFTP server.
  3. The current configuration is saved to config.cfg in the flash but is not used for the startup-config.
  4. The current configuration is saved to config.cfg in the flash and is used for the startup-config.
Correct answer: D
Question 8
A customer is implementing a network using HP ProVision switches. Which default setting applies to the ProVision switches?
  1. All ports are disabled.
  2. Routing is enabled.
  3. Telnet is enabled.
  4. A static IP address is assigned to VLAN 1.
Correct answer: C
Question 9
A company needs a two-member Intelligent Resilient Framework (IRF) virtual switch. The network administrator is configuring IRF member 2 that will connect to port 1/1 on IRF member 1. What is the correct IRF port ID for member 2?
  1. 1/2
  2. 2/2
  3. 1/1
  4. 2/1
Correct answer: B
Question 10
A customer wants to implement multiple links between a server and a single HP Comware switch in order to increase the amount of bandwidth for more throughput. 
Which feature should the network administrator implement to accomplish this?
  1. MSTP
  2. IRF
  3. link aggregation
  4. MIMO
Correct answer: B
CONNECT US
HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset

HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen

ProfExam
ProfExam at a 20% markdown

You have the opportunity to purchase ProfExam at a 20% reduced price

Get Now!