Download Specialist - Implementation Engineer, PowerEdge MX Modular Exam.DES-4421.CertKiller.2019-12-04.32q.vcex

Vendor: Dell
Exam Code: DES-4421
Exam Name: Specialist - Implementation Engineer, PowerEdge MX Modular Exam
Date: Dec 04, 2019
File Size: 23 KB

How to open VCEX files?

Files with VCEX extension can be opened by ProfExam Simulator.

Demo Questions

Question 1
A server sled has a single mezzanine card installed in the correctly supported slot. 
To which IOM fabric(s) does the sled have access?
  1. Fabric A1 and Fabric A2
  2. Fabric A1 only
  3. Either Fabric A or Fabric B, depending on the configuration set in OME-M
  4. Fabric A1 and Fabric B1
Correct answer: B
Explanation:
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/dell_emc_poweredge_mx7000_technical_guide.pdf
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/dell_emc_poweredge_mx7000_technical_guide.pdf
Question 2
What is the number of server-facing ports and the bandwidth of each port on the MXG610s? (Choose two.)
  1. 8x 16 Gbps
  2. 16x 32 Gbps
  3. 16x 16 Gbps
  4. 8x 32 Gbps
Correct answer: BC
Explanation:
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/DellEMCNetworkingMXG610sSpecSheet.pdf (page 1)
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/DellEMCNetworkingMXG610sSpecSheet.pdf (page 1)
Question 3
A company has several MX7000-systems, four FX2 solutions, one M1000e, and several PowerEdge rack servers. 
Which management interface is recommended for managing this range of systems?
  1. OpenManage Modular, no optional plugins required
  2. OpenManage Essentials
  3. OpenManage Modular with optional plugins
  4. OpenManage Enterprise
Correct answer: D
Explanation:
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/PowerEdge-Modular-Quick-Reference-Guide.pdf
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/PowerEdge-Modular-Quick-Reference-Guide.pdf
Question 4
An administrator is about to perform a firmware update on an MX9116n switch OS 10 from the CLI. The latest OS 10 switch firmware image has been downloaded and their TFTP server is set up. 
Upon logged in with administrator credentials on the switch, which command should be used to start the update procedure?
  1. firmwaredownload tftp://server-ip/imagename
  2. install tftp://server-ip/imagename
  3. fwupdate tftp://server-ip/imagename
  4. upgrade tftp://server-ip/imagename
Correct answer: B
Explanation:
Reference: https://topics-cdn.dell.com/pdf/smartfabric-os10-5-0_en-us.pdf
Reference: https://topics-cdn.dell.com/pdf/smartfabric-os10-5-0_en-us.pdf
Question 5
What is a characteristic of MX7000 networking in Scalable Fabric Mode?
  1. Enabled by default, all switch-specific OS10EE capabilities are available.
  2. Layer 2 bridging is disabled be default and interfaces must join a bridge domain (VLAN) before being to forward frames.
  3. All switch interfaces are assigned to VLAN 1 by default and are in the same Layer 2 bridge domain.
  4. Available on MX9116n FSE and MX7116n FEM but not on the MX5108n.
Correct answer: D
Explanation:
Reference: https://hasanmansur.com/2019/01/10/mx7000-networking-part-2-operating-modes-iom-selection/
Reference: https://hasanmansur.com/2019/01/10/mx7000-networking-part-2-operating-modes-iom-selection/
Question 6
Which I/O module is supported for Fabric B?
  1. MX5016s
  2. MSG610s
  3. MX5000s
  4. MX5108n
Correct answer: D
Explanation:
Reference: https://hasanmansur.com/2019/01/08/mx7000-networking-part-1-introduction-components/
Reference: https://hasanmansur.com/2019/01/08/mx7000-networking-part-1-introduction-components/
Question 7
What is a valid option when resetting iDRAC to factory defaults?
  1. Preserve user and network settings
  2. Preserve network and storage settings
  3. Preserve identity and network settings
  4. Preserve storage and user settings
Correct answer: A
Explanation:
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-r740/idrac_3.21.21.21_ug/reset-idrac-and-reset-idrac-to-default?guid=guid-1b5c2d57-05c8-4098-8344-49c984839c30&lang=en-us
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-r740/idrac_3.21.21.21_ug/reset-idrac-and-reset-idrac-to-default?guid=guid-1b5c2d57-05c8-4098-8344-49c984839c30&lang=en-us
Question 8
What is a characteristic of MX7000 networking in Full Switch Mode?
  1. Layer 2 bridging is disabled by default and interfaces must join a bridge domain (VLAN) before being able to forward frames.
  2. Networking is enabled by default and all switch-specific OS10EE capabilities are available.
  3. Networking is available on MX9116n FSE and MX7116n FEM but not on the MX5108n.
  4. Switches operate as layer 2 I/O aggregation devices and are managed through OME-M.
Correct answer: B
Explanation:
Reference: https://infohub.delltechnologies.com/l/test2-poweredge-mx-networking-architecture-guide-1/operating-modes-description-7
Reference: https://infohub.delltechnologies.com/l/test2-poweredge-mx-networking-architecture-guide-1/operating-modes-description-7
Question 9
In an MX7000, which components are cooled by the rear fans?
  1. Fabric A, B, and C IOMs only
  2. All compute and storage sleds
  3. Management Modules only
  4. Fabric A, B, and C IOMs and the Management Modules
Correct answer: D
Explanation:
Reference: http://bladesmadesimple.com/2018/08/a-first-look-at-the-dell-emc-poweredge-mx/
Reference: http://bladesmadesimple.com/2018/08/a-first-look-at-the-dell-emc-poweredge-mx/
Question 10
Which controller option the mapping of an entire MX5016s to multiple compute sleds?
  1. PERC H730 only
  2. HBA330 only
  3. H745 Jumbo PERC
  4. HBA330 and PERC H730
Correct answer: B
Explanation:
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-mx7000/pemx5016s_mx5000s_ism/initial-system-setup-and-configuration-for-mx5016s?guid=guid-f5a47d05-b0f9-4573-aa98-350a7e7a2c3c&lang=en-us
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-mx7000/pemx5016s_mx5000s_ism/initial-system-setup-and-configuration-for-mx5016s?guid=guid-f5a47d05-b0f9-4573-aa98-350a7e7a2c3c&lang=en-us
Question 11
A server sled has a single mezzanine card installed in the correctly supported slot. 
To which IOM fabric(s) does the sled have access?
  1. Fabric A1 and Fabric A2
  2. Fabric A1 only
  3. Either Fabric A or Fabric B, depending on the configuration set in OME-M
  4. Fabric A1 and Fabric B1
Correct answer: B
Explanation:
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/dell_emc_poweredge_mx7000_technical_guide.pdf
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/dell_emc_poweredge_mx7000_technical_guide.pdf
Question 12
What is the number of server-facing ports and the bandwidth of each port on the MXG610s? (Choose two.)
  1. 8x 16 Gbps
  2. 16x 32 Gbps
  3. 16x 16 Gbps
  4. 8x 32 Gbps
Correct answer: BC
Explanation:
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/DellEMCNetworkingMXG610sSpecSheet.pdf (page 1)
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/DellEMCNetworkingMXG610sSpecSheet.pdf (page 1)
Question 13
A company has several MX7000-systems, four FX2 solutions, one M1000e, and several PowerEdge rack servers. 
Which management interface is recommended for managing this range of systems?
  1. OpenManage Modular, no optional plugins required
  2. OpenManage Essentials
  3. OpenManage Modular with optional plugins
  4. OpenManage Enterprise
Correct answer: D
Explanation:
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/PowerEdge-Modular-Quick-Reference-Guide.pdf
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/PowerEdge-Modular-Quick-Reference-Guide.pdf
Question 14
An administrator is about to perform a firmware update on an MX9116n switch OS 10 from the CLI. The latest OS 10 switch firmware image has been downloaded and their TFTP server is set up. 
Upon logged in with administrator credentials on the switch, which command should be used to start the update procedure?
  1. firmwaredownload tftp://server-ip/imagename
  2. install tftp://server-ip/imagename
  3. fwupdate tftp://server-ip/imagename
  4. upgrade tftp://server-ip/imagename
Correct answer: B
Explanation:
Reference: https://topics-cdn.dell.com/pdf/smartfabric-os10-5-0_en-us.pdf
Reference: https://topics-cdn.dell.com/pdf/smartfabric-os10-5-0_en-us.pdf
Question 15
What is a characteristic of MX7000 networking in Scalable Fabric Mode?
  1. Enabled by default, all switch-specific OS10EE capabilities are available.
  2. Layer 2 bridging is disabled be default and interfaces must join a bridge domain (VLAN) before being to forward frames.
  3. All switch interfaces are assigned to VLAN 1 by default and are in the same Layer 2 bridge domain.
  4. Available on MX9116n FSE and MX7116n FEM but not on the MX5108n.
Correct answer: D
Explanation:
Reference: https://hasanmansur.com/2019/01/10/mx7000-networking-part-2-operating-modes-iom-selection/
Reference: https://hasanmansur.com/2019/01/10/mx7000-networking-part-2-operating-modes-iom-selection/
Question 16
Which I/O module is supported for Fabric B?
  1. MX5016s
  2. MSG610s
  3. MX5000s
  4. MX5108n
Correct answer: D
Explanation:
Reference: https://hasanmansur.com/2019/01/08/mx7000-networking-part-1-introduction-components/
Reference: https://hasanmansur.com/2019/01/08/mx7000-networking-part-1-introduction-components/
Question 17
What is a valid option when resetting iDRAC to factory defaults?
  1. Preserve user and network settings
  2. Preserve network and storage settings
  3. Preserve identity and network settings
  4. Preserve storage and user settings
Correct answer: A
Explanation:
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-r740/idrac_3.21.21.21_ug/reset-idrac-and-reset-idrac-to-default?guid=guid-1b5c2d57-05c8-4098-8344-49c984839c30&lang=en-us
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-r740/idrac_3.21.21.21_ug/reset-idrac-and-reset-idrac-to-default?guid=guid-1b5c2d57-05c8-4098-8344-49c984839c30&lang=en-us
Question 18
What is a characteristic of MX7000 networking in Full Switch Mode?
  1. Layer 2 bridging is disabled by default and interfaces must join a bridge domain (VLAN) before being able to forward frames.
  2. Networking is enabled by default and all switch-specific OS10EE capabilities are available.
  3. Networking is available on MX9116n FSE and MX7116n FEM but not on the MX5108n.
  4. Switches operate as layer 2 I/O aggregation devices and are managed through OME-M.
Correct answer: B
Explanation:
Reference: https://infohub.delltechnologies.com/l/test2-poweredge-mx-networking-architecture-guide-1/operating-modes-description-7
Reference: https://infohub.delltechnologies.com/l/test2-poweredge-mx-networking-architecture-guide-1/operating-modes-description-7
Question 19
In an MX7000, which components are cooled by the rear fans?
  1. Fabric A, B, and C IOMs only
  2. All compute and storage sleds
  3. Management Modules only
  4. Fabric A, B, and C IOMs and the Management Modules
Correct answer: D
Explanation:
Reference: http://bladesmadesimple.com/2018/08/a-first-look-at-the-dell-emc-poweredge-mx/
Reference: http://bladesmadesimple.com/2018/08/a-first-look-at-the-dell-emc-poweredge-mx/
Question 20
Which controller option the mapping of an entire MX5016s to multiple compute sleds?
  1. PERC H730 only
  2. HBA330 only
  3. H745 Jumbo PERC
  4. HBA330 and PERC H730
Correct answer: B
Explanation:
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-mx7000/pemx5016s_mx5000s_ism/initial-system-setup-and-configuration-for-mx5016s?guid=guid-f5a47d05-b0f9-4573-aa98-350a7e7a2c3c&lang=en-us
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-mx7000/pemx5016s_mx5000s_ism/initial-system-setup-and-configuration-for-mx5016s?guid=guid-f5a47d05-b0f9-4573-aa98-350a7e7a2c3c&lang=en-us
Question 21
A server sled has a single mezzanine card installed in the correctly supported slot. 
To which IOM fabric(s) does the sled have access?
  1. Fabric A1 and Fabric A2
  2. Fabric A1 only
  3. Either Fabric A or Fabric B, depending on the configuration set in OME-M
  4. Fabric A1 and Fabric B1
Correct answer: B
Explanation:
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/dell_emc_poweredge_mx7000_technical_guide.pdf
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/dell_emc_poweredge_mx7000_technical_guide.pdf
Question 22
What is the number of server-facing ports and the bandwidth of each port on the MXG610s? (Choose two.)
  1. 8x 16 Gbps
  2. 16x 32 Gbps
  3. 16x 16 Gbps
  4. 8x 32 Gbps
Correct answer: BC
Explanation:
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/DellEMCNetworkingMXG610sSpecSheet.pdf (page 1)
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/DellEMCNetworkingMXG610sSpecSheet.pdf (page 1)
Question 23
A company has several MX7000-systems, four FX2 solutions, one M1000e, and several PowerEdge rack servers. 
Which management interface is recommended for managing this range of systems?
  1. OpenManage Modular, no optional plugins required
  2. OpenManage Essentials
  3. OpenManage Modular with optional plugins
  4. OpenManage Enterprise
Correct answer: D
Explanation:
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/PowerEdge-Modular-Quick-Reference-Guide.pdf
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/PowerEdge-Modular-Quick-Reference-Guide.pdf
Question 24
An administrator is about to perform a firmware update on an MX9116n switch OS 10 from the CLI. The latest OS 10 switch firmware image has been downloaded and their TFTP server is set up. 
Upon logged in with administrator credentials on the switch, which command should be used to start the update procedure?
  1. firmwaredownload tftp://server-ip/imagename
  2. install tftp://server-ip/imagename
  3. fwupdate tftp://server-ip/imagename
  4. upgrade tftp://server-ip/imagename
Correct answer: B
Explanation:
Reference: https://topics-cdn.dell.com/pdf/smartfabric-os10-5-0_en-us.pdf
Reference: https://topics-cdn.dell.com/pdf/smartfabric-os10-5-0_en-us.pdf
Question 25
What is a characteristic of MX7000 networking in Scalable Fabric Mode?
  1. Enabled by default, all switch-specific OS10EE capabilities are available.
  2. Layer 2 bridging is disabled be default and interfaces must join a bridge domain (VLAN) before being to forward frames.
  3. All switch interfaces are assigned to VLAN 1 by default and are in the same Layer 2 bridge domain.
  4. Available on MX9116n FSE and MX7116n FEM but not on the MX5108n.
Correct answer: D
Explanation:
Reference: https://hasanmansur.com/2019/01/10/mx7000-networking-part-2-operating-modes-iom-selection/
Reference: https://hasanmansur.com/2019/01/10/mx7000-networking-part-2-operating-modes-iom-selection/
Question 26
Which I/O module is supported for Fabric B?
  1. MX5016s
  2. MSG610s
  3. MX5000s
  4. MX5108n
Correct answer: D
Explanation:
Reference: https://hasanmansur.com/2019/01/08/mx7000-networking-part-1-introduction-components/
Reference: https://hasanmansur.com/2019/01/08/mx7000-networking-part-1-introduction-components/
Question 27
What is a valid option when resetting iDRAC to factory defaults?
  1. Preserve user and network settings
  2. Preserve network and storage settings
  3. Preserve identity and network settings
  4. Preserve storage and user settings
Correct answer: A
Explanation:
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-r740/idrac_3.21.21.21_ug/reset-idrac-and-reset-idrac-to-default?guid=guid-1b5c2d57-05c8-4098-8344-49c984839c30&lang=en-us
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-r740/idrac_3.21.21.21_ug/reset-idrac-and-reset-idrac-to-default?guid=guid-1b5c2d57-05c8-4098-8344-49c984839c30&lang=en-us
Question 28
What is a characteristic of MX7000 networking in Full Switch Mode?
  1. Layer 2 bridging is disabled by default and interfaces must join a bridge domain (VLAN) before being able to forward frames.
  2. Networking is enabled by default and all switch-specific OS10EE capabilities are available.
  3. Networking is available on MX9116n FSE and MX7116n FEM but not on the MX5108n.
  4. Switches operate as layer 2 I/O aggregation devices and are managed through OME-M.
Correct answer: B
Explanation:
Reference: https://infohub.delltechnologies.com/l/test2-poweredge-mx-networking-architecture-guide-1/operating-modes-description-7
Reference: https://infohub.delltechnologies.com/l/test2-poweredge-mx-networking-architecture-guide-1/operating-modes-description-7
Question 29
In an MX7000, which components are cooled by the rear fans?
  1. Fabric A, B, and C IOMs only
  2. All compute and storage sleds
  3. Management Modules only
  4. Fabric A, B, and C IOMs and the Management Modules
Correct answer: D
Explanation:
Reference: http://bladesmadesimple.com/2018/08/a-first-look-at-the-dell-emc-poweredge-mx/
Reference: http://bladesmadesimple.com/2018/08/a-first-look-at-the-dell-emc-poweredge-mx/
Question 30
Which controller option the mapping of an entire MX5016s to multiple compute sleds?
  1. PERC H730 only
  2. HBA330 only
  3. H745 Jumbo PERC
  4. HBA330 and PERC H730
Correct answer: B
Explanation:
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-mx7000/pemx5016s_mx5000s_ism/initial-system-setup-and-configuration-for-mx5016s?guid=guid-f5a47d05-b0f9-4573-aa98-350a7e7a2c3c&lang=en-us
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-mx7000/pemx5016s_mx5000s_ism/initial-system-setup-and-configuration-for-mx5016s?guid=guid-f5a47d05-b0f9-4573-aa98-350a7e7a2c3c&lang=en-us
HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset

HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen

ProfExam
ProfExam at a 20% markdown

You have the opportunity to purchase ProfExam at a 20% reduced price

Get Now!