Download Cisco.Testkings.300-115.v10-0.2016-06-08.1e.166q.vcex

Download Dump

File Info

Exam Implementing Cisco IP Switched Networks (SWITCH v2.0)
Number 300-115
File Name Cisco.Testkings.300-115.v10-0.2016-06-08.1e.166q.vcex
Size 5.31 Mb
Posted June 08, 2016
Downloaded 8



How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Purchase
Coupon: EXAMFILESCOM

Coupon: EXAMFILESCOM
With discount: 20%





Demo Questions

Question 1
What is the maximum number of switches that can be stacked using Cisco StackWise?

  • A: 4
  • B: 5
  • C: 8
  • D: 9
  • E: 10
  • F: 13



Question 2
A network engineer wants to add a new switch to an existing switch stack. Which configuration must be added to the new switch before it can be added to the switch stack?

  • A: No configuration must be added.
  • B: stack ID
  • C: IP address
  • D: VLAN information
  • E: VTP information



Question 3
What percentage of bandwidth is reduced when a stack cable is broken?

  • A: 0
  • B: 25
  • C: 50
  • D: 75
  • E: 100



Question 4
A network engineer notices inconsistent Cisco Discovery Protocol neighbors according to the diagram that is provided. The engineer notices only a single neighbor that uses Cisco Discovery Protocol, but it has several routing neighbor relationships. What would cause the output to show only the single neighbor? 


  • A: The routers are connected via a Layer 2 switch.
  • B: IP routing is disabled on neighboring devices.
  • C: Cisco Express Forwarding is enabled locally.
  • D: Cisco Discovery Protocol advertisements are inconsistent between the local and remote devices.



Question 5
After the implementation of several different types of switches from different vendors, a network engineer notices that directly connected devices that use Cisco Discovery Protocol are not visible. Which vendor-neutral protocol could be used to resolve this issue?

  • A: Local Area Mobility
  • B: Link Layer Discovery Protocol
  • C: NetFlow
  • D: Directed Response Protocol



Question 6
Several new switches have been added to the existing network as VTP clients. All of the new switches have been configured with the same VTP domain, password, and version. However, VLANs are not passing from the VTP server (existing network) to the VTP clients. What must be done to fix this?

  • A: Remove the VTP domain name from all switches with "null" and then replace it with the new domain name.
  • B: Configure a different native VLAN on all new switches that are configured as VTP clients.
  • C: Provision one of the new switches to be the VTP server and duplicate information from the existing network.
  • D: Ensure that all switch interconnects are configured as trunks to allow VTP information to be transferred.



Question 7
After implementing VTP, the extended VLANs are not being propagated to other VTP switches. What should be configured for extended VLANs?

  • A: VTP does not support extended VLANs and should be manually added to all switches.
  • B: Enable VTP version 3, which supports extended VLAN propagation. 
  • C: VTP authentication is required when using extended VLANs because of their ability to cause network instability.
  • D: Ensure that all switches run the same Cisco IOS version. Extended VLANs will not propagate to different IOS versions when extended VLANs are in use.



Question 8
Refer to the exhibit. 
 
  
Switch A, B, and C are trunked together and have been properly configured for VTP. Switch C receives VLAN information from the VTP server Switch A, but Switch B does not receive any VLAN information. What is the most probable cause of this behavior?

  • A: Switch B is configured in transparent mode.
  • B: Switch B is configured with an access port to Switch A, while Switch C is configured with a trunk port to Switch B.
  • C: The VTP revision number of the Switch B is higher than that of Switch A.
  • D: The trunk between Switch A and Switch B is misconfigured.



Question 9
Refer to the exhibit. 
 
  
Switch A, B, and C are trunked together and have been properly configured for VTP. Switch B has all VLANs, but Switch C is not receiving traffic from certain VLANs. What would cause this issue?

  • A: A VTP authentication mismatch occurred between Switch A and Switch B.
  • B: The VTP revision number of Switch B is higher than that of Switch A.
  • C: VTP pruning is configured globally on all switches and it removed VLANs from the trunk interface that is connected to Switch C.
  • D: The trunk between Switch A and Switch B is misconfigured.



Question 10
After the recent upgrade of the switching infrastructure, the network engineer notices that the port roles that were once “blocking” are now defined as “alternate” and “backup.” What is the reason for this change? 


  • A: The new switches are using RSTP instead of legacy IEEE 802.1D STP.
  • B: IEEE 802.1D STP and PortFast have been configured by default on all newly implemented Cisco Catalyst switches.
  • C: The administrator has defined the switch as the root in the STP domain.
  • D: The port roles have been adjusted based on the interface bandwidth and timers of the new Cisco Catalyst switches.









CONNECT US


ProfExam
PROFEXAM WITH A 20% DISCOUNT

You can buy ProfExam with a 20% discount..

Get Now!


HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen



HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset