Download Building HP FlexFabric Data Centers.CertDumps.HP2-Z34.2018-07-25.1e.31q.vcex

Download Exam

File Info

Exam Building HP FlexFabric Data Centers
Number HP2-Z34
File Name Building HP FlexFabric Data Centers.CertDumps.HP2-Z34.2018-07-25.1e.31q.vcex
Size 1.47 Mb
Posted July 25, 2018
Downloads 25

How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.


With discount: 20%


Demo Questions

Question 1
A large data center needs to extend its Layer 2 connectivity and isolate tenants who might use the same VLAN IDs Which technology accomplishes this goal?

  • A: SPBM
  • B: Data Center Bridging (DCB)
  • C: Multi-VPN-Instance CE (MCE)
  • D: TRILL

Question 2
To provide redundancy, a company has multiple data centers that use server virtualization. What is a networking requirement for this scenario?

  • A: less bandwidth at the server access layer and more bandwidth at the distribution layer than in a non-virtualized network
  • B: physical network segmentation and isolation implemented at Layers 1 through 7
  • C: localized storage volumes that are isolated within each data center
  • D: extension of Layer 2 connectivity across the data centers

Question 3
Refer to the exhibit 


The exhibit displays a company with two data centers that connect by using EVl. The company needs a redundant solution for routing traffic between the subnets. 
What is the best way to accomplish this goal?

  • A: Run Virtual Router Redundancy Protocol (VRRP) on the data center subnets
  • B: Place the EVl tunnel interface on each IRF virtual device in a different VPN instance, and then set up routing on each device by using the same IP addresses.
  • C: Use TRILL on the EVl network.
  • D: Combine IRF 1 and IRF 2 into the same IRF virtual device, and set up routing on that device

Question 4
In addition to the Admin MDC, an HP Comware switch supports two MDCs: MDC 2 and MDC 3. The administrator wants to allow tenants for both MDCs to log in to CLI for their own MDC without first accessing the Admin MDC How can the administrator accomplish this goal?

  • A: Assign a console port to each MDC Tenants can then connect their own terminal equipment to their assigned port.
  • B: Define a VLAN as the MDC Management VLAN in the Admin MDC. On each MDC. create this VLAN. Assign a port to it. Set up an IP address on it and set up Telnet or SSH access through it.
  • C: Create subinterfaces for the AUX user-interface in the Admin MDC. Assign one of the subinterfaces to each of the MDCs. and set up Telnet or SSH access through that interface
  • D: Define a physical port as the Management-Ethernet interface in the Admin MDC On each MDC. Configure a different IP address for this interface, and set up Telnet or SSH access through it.

Question 5
What is the purpose of the nickname in TRILL switch settings?

  • A: The nickname identifies the TRILL region and must match on every TRILL RBridge in the region.
  • B: Administrators can use the nicknames to identify switches in CLI output.
  • C: The nickname is the first factor for electing a root bridge
  • D: TRILL RBridges use the nicknames as source and destination addresses in TRILL headers

Question 6
Several VPN instances have been set up on an HP Comware switch. What should the administrator do to ensure that no VPN instance uses up too many switch resources?

  • A: Apply a service policy to each instance to assign that instance a percentage of resources
  • B: Bind each instance to a specific port group or ASIC
  • C: Set a maximum number of routes that each instance can have in its routing table.
  • D: Set a CPU weight for each VPN instance to control how much of the CPU the instance can use.

Question 7
Refer to the exhibit 

The company wants to use TRILL in the backbone links shown in the exhibit. Servers use VLANs 10, 20, and 30 and should be able to communicate across the backbone. On which Switch 1 interfaces should the administrator enable TRILL?

  • A: VLAN interface 1 only
  • B: VLAN interfaces 1,10, 20, and 30
  • C: interfaces Forty1/0/49 and Forty1/0/50 only
  • D: interfaces Ten1/0/1 to Ten1/0/48, and Forty1/0/49 and Forty1/0/50

Question 8
An HP Comware Switch 1 supports FCoE for connected servers with Converged Network Adapters (CNAs). On interface Ten 1/0/1  Switch 1 sends FCoE traffic in VSAN 2 to an upstream switch. Switch 2 which also supports FCoE What is the correct configuration for interface Ten 1/071?

  • A: FC trunk port, which permits VSAN 2
  • B: bound to a VFC interface, which is a trunk port and permits VSAN 2
  • C: bound to a VFC interface, which is an access port in VSAN 2
  • D: FC access port in VSAN 2

Question 9
An HP Comware switch supports FCoE in Fibre Channel Forwarder (FCF) mode. A switch interface Ten1/0/1 connects to a server FCoE Converged Network Adapter (CNA). The CNA will carry normal data traffic and storage traffic for VSAN 2. which is associated with VLAN 20. How does the administrator assign FCoE traffic for this CNA to VSAN 2?

  • A: by accessing the VSAN 2 configuration view and specifying Ten1/0/1 as a member port of the VSAN
  • B: by accessing the VLAN 20 configuration view and specifying Ten1/0/1 as a member port of the VLAN
  • C: by setting Ten1/0/1 to FCoE mode and specifying VSAN 2 as the port access VSAN
  • D: by binding a VFC interface to Ten 1/0/1 and specifying VSAN 2 as the VFC interface trunk VSAN

Question 10
Refer to the exhibit 


An administrator is setting up this data center topology to use SPBM VMs in the same subnet should be able to communicate at Layer 2 and be isolated at Layer 2 from other subnets. On which Switch 1 interfaces should the administrator enable SPBM?

  • A: interfaces Ten1/0/1-Ten1/0/48 and interfaces Forty1/0749-1/0750
  • B: interfaces Forty 1/0749-1/075€ only
  • C: VLAN interfaces 101 and 103
  • D: VLAN interfaces 10, 20, and 30


You can buy ProfExam with a 20% discount..

Get Now!


Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen


Use VCE Exam Simulator to open VCE files