Download Cisco.PracticeDumps.642-883.2018-01-05.1e.174q.vcex

Download Dump

File Info

Exam Deploying Cisco Service Provider Network Routing (SPROUTE)
Number 642-883
File Name Cisco.PracticeDumps.642-883.2018-01-05.1e.174q.vcex
Size 8.83 Mb
Posted July 24, 2018
Downloaded 1



How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Purchase
Coupon: EXAMFILESCOM

Coupon: EXAMFILESCOM
With discount: 20%





Demo Questions

Question 1
Refer to the OSPF command exhibit. 
 
  

Which effect does the no-summary command option have?

  • A: It will cause area 1 to be able to receive non-summarized inter-area routes.
  • B: It will cause area 1 to not receive any inter-area routes and will use a default route to reach networks in other areas.
  • C: It will cause area 1 to not receiveany external routes and will use a default route to reach the external networks.
  • D: It will convert the NSSA area into a NSSA totally stubby area.
  • E: It will convert the stubby area into a NSSA.
  • F: It will disable OSPF auto-summary.



Question 2
When troubleshooting OSPF neighbor errors, which three verification steps should be considered? (Choose three.)

  • A: Verify if neighboring OSPF interfaces are configured in the same area.
  • B: Verify if neighboring OSPF interfaces are configured with the same OSPF process ID.
  • C: Verify if neighboring OSPF interfaces are configured with the same OSPF priority.
  • D: Verify if neighboring OSPF interfaces are configured with the same hello and dead intervals.
  • E: Verify if neighboring OSPF interfaces are configured with the same area type.



Question 3
On Cisco IOS XR Software, which set of commands is used to enable the gi0/0/0/1 interface for OSPF in area 0?

  • A: interface gi0/0/0/0ip address 10.1.1.1255.255.255.0!router ospf 1network 10.1.1.1 0.0.0.0 area 0
  • B: interface gi0/0/0/0ip address 10.1.1.1 255.255.255.0!router ospf 1network 10.1.1.1 255.255.255.255 area 0
  • C: router ospf 1area 0interface GigabitEthernet0/0/0/1
  • D: interface gi0/0/0/0ip address10.1.1.1 255.255.255.0ip ospf 1 area 0
  • E: router ospf 1address-family ipv4 unicastinterface GigabitEthernet0/0/0/1 area 0
  • F: router ospf 1address-family ipv4 unicastinterface GigabitEthernet0/0/0/1area 0



Question 4
Which three statements are true regarding the OSPF router ID? (Choose three.)

  • A: The OSPF routing process chooses a router ID for itself when it starts up.
  • B: The router-id command is the preferred procedure to set the router ID.
  • C: If a loopback interface is configured, its address will always be preferred as the router ID over any other methods.
  • D: After the router ID is set, it does not change, even if the interface that the router is using for the router ID goes down. The router ID changes only if the routerreloads or if the OSPF routing process restarts.
  • E: In OSPF version 3, the OSPF router ID uses a 128-bit number.



Question 5
Which two OSPF network scenarios require OSPF virtual link configuration? (Choose two.)

  • A: to connect an OSPF non-backbone area to area 0 through another non-backbone area
  • B: to connect an NSSA area to an external routing domain
  • C: to connect two parts of a partitioned backbone area through a non-backbone area
  • D: to enable route leaking from Level 2into Level 1
  • E: to enable route leaking from Level 1 into Level 2
  • F: to enable OSPF traffic engineering



Question 6
What is function of the RP/0/RSP0/CPU0:PE1(config-ospf)#distance Cisco IOS-XR command?

  • A: To modify the administrative distance of the OSPF routes
  • B: To modify the default seed metric of the OSPF external routes
  • C: To modify the OSPF default reference bandwidth
  • D: To modify the OSPF cost



Question 7
Which four statements are correct regarding IS-IS operations? (Choose four.)

  • A: By default, Level 1 routers within an IS-IS area do not carry any routing information external to the area towhich they belong. They use a default route to exit the area.
  • B: Summarization should be configured on the Level 2 routers, which injects the Level 2 routes into Level 1.
  • C: IS-IS supports "route leaking" in which selected Level 2 routes can be advertisedby a Level 1/Level 2 router into Level 1.
  • D: The IS-IS backbone is a contiguous collection of Level 1 capable routers, each of which can be in a different area.
  • E: With IS-IS, an individual router is in only one area, and the border between areas is on thelink that connects two routers that are in different areas.
  • F: Cisco IOS XR Software supports multitopology for IPv6 IS-IS unless single topology is explicitly configured in IPv6 address-family configuration mode.



Question 8
When configuring IPv4 and IPv6 IS-IS routing on Cisco IOS XR routers, which three statements are correct? (Choose three.)

  • A: By default, a single SPF is used for both IPv4 and IPv6, so the IPv4 and IPv6 topology should be the same.
  • B: By default, the IS-IS router type is Level 1 and Level 2.
  • C: All IS-IS routers within the same IS-IS area must be configured with the same IS-IS routing process instance ID.
  • D: By default,metric-style narrow is used.
  • E: By default, the IS-IS interface circuit type is Level 1 and Level 2.
  • F: The area IS-IS address-family configuration command is used to specify the IS-IS area address.



Question 9
Refer to the PE1 router routing table output exhibit. 
 
  

What is causing the i su 10.1.10.0/24 [115/30] via 0.0.0.0, 00:40:34, Null0 entry on the PE1 router routing table?

  • A: The PE1 router is receiving the 10.1.10.0/24 summary route from the upstream L1/L2 IS-IS router.
  • B: The PE1 router has been configured to summarize the 10.1.10.x/32 IS-IS routes to 10.1.10.0/24.
  • C: The 10.1.10.0/24 has been suppressed because IS-IS auto-summary has been disabled on the PE1 router.
  • D: The 10.1.10.0/24 has been suppressed because of a route policy configuration on the PE1 router.
  • E: The 10.1.10.0/24 has been suppressed because the more specific 10.1.10.x/32 IS-IS routes have been configured to leak into the IS-IS non-backbone area.



Question 10
In comparing IS-IS with OSPF, a Level-1-2 IS-IS router is similar to which kind of OSPF router?

  • A: ASBR on a normal OSPF area
  • B: ASBR on NSSA
  • C: ABR on totally stubby OSPF area
  • D: ABR on stubbyOSPF area
  • E: ABR on a normal OSPF area









CONNECT US


ProfExam
PROFEXAM WITH A 20% DISCOUNT

You can buy ProfExam with a 20% discount..

Get Now!


HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen



HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset