Download Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR).passcertification.350-401.2020-01-09.1e.28q.vcex


Download Exam

File Info

Exam Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)
Number 350-401
File Name Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR).passcertification.350-401.2020-01-09.1e.28q.vcex
Size 668 Kb
Posted January 09, 2020
Downloads 115



How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Purchase
Coupon: EXAMFILESCOM

Coupon: EXAMFILESCOM
With discount: 20%


 
 



Demo Questions

Question 1
Which statement about WAN Ethernet Services is true?

  • A: Rate-limiting can be configured per EVC.
  • B: Point-to-point processing and encapsulation are performed on the customer network.
  • C: Ethernet multipoint services function as a multipoint-to-multipoint VLAN-based connection.
  • D: UNIscan perform service multiplexing and all-in-one bundling.



Question 2
Which statement about the OSPF Loop-Free Alternate feature is true?

  • A: It is supported on routers that are configured with virtual links.
  • B: It is supported in VRF OSPF instances.
  • C: It is supported when a traffic engineering tunnel interface is protected.
  • D: It is supported when traffic can be redirected to a primary neighbor.



Question 3
  

Refer to the exhibit. You have configured a VRF named Blue on R1 as shown. Which action must you take to enable uRPF on the R1 interface E1/0?

  • A: Configure the ip verify vrf Blue unicast source reachable-via rx allow-default command on interface E1/0.
  • B: Configure the ip verify unicast source reachable-via rx allow-default command under the VRF Blue process.
  • C: Configure the ip verify vrf Blue unicast source reachable-via rx allow-default command on interface E0/1.
  • D: Configure the ip verify unicast source reachable-via rx allow-default command on interface E1/0.
  • E: Configure the ip verify vrf Blue unicast source reachable-via rx allow-default command under the VRF Blue process.



Question 4
Which two statements about DMVPN with NHRP are true? (Choose two.)

  • A: The spoke routers act as the NHRP servers.
  • B: NHRP disables multicast.
  • C: The hub router uses NHRP to initiate the GRE tunnel with spokes.
  • D: NHRP dynamically provides information about the spoke routers to the hub.
  • E: NHRP shortens the configuration of the hub router.



Question 5
Refer to the exhibit. 

  

Which two possible network conditions can you infer from this configuration? (Choose two.)

  • A: The authentication parameters on R1 and R2 are mismatched.
  • B: R1 is using the default NTP source configuration.
  • C: R1 and R2 have established an NTP session.
  • D: R2 is configured as the NTP master with a stratum of 7.



Question 6
Drag each NTP command on the left to its effect on the right.  




Question 7
What are the three variants of NTPv4? (Choose three.)

  • A: symmetric
  • B: unicast
  • C: client/server
  • D: broadcast
  • E: multicast
  • F: asymmetric



Question 8
Which three statements about EVCs are true? (Choose three.)

  • A: Spanning Tree must use RSTP mode on EVC ports.
  • B: Spanning Tree must use MST mode on EVC ports.
  • C: LACP is supported on EVC ports.
  • D: Layer 2 multicast framing is supported.
  • E: Bridge domain routing is required.
  • F: PAGP is supported on EVC ports.



Question 9
  

Refer to the exhibit. The Main1 and Branch1 switches are connected directly over an MPLS pseudowire, and both run UDLD. After router B1 reloads because of a power failure, the pseudowire is restored. However, the Branch1 switch is unable to reach the Main1 switch. 
Which two actions can you take to restore connectivity and prevent the problem from recurring? (Choose two.)

  • A: Issue the shutdown and no shutdown commands on the Branch1 switch uplink to the B1 router only.
  • B: Configure a backup GRE tunnel between the Main1 and Branch1switches.
  • C: Issue the shutdown and no shutdown commands on both the Branch1 switch uplink to the B1 router and the Main1 switch’s uplink to the M1 router.
  • D: Configure a backup pseudowire between the Main1 and Branch1 switches.
  • E: Enable UDLD recovery on both the Main1 and Branch1 switches.
  • F: Enable errdisable recovery on both the Main1 and Branch1 switches.



Question 10
  

Refer to the exhibit. While reviewing a log file on a router with this NTP configuration, you note that the log entries of the router display a different time than the NTP time. Which action can you take to correct the problem?

  • A: Remove the datetime keyword from the service timestamps log datetimestatement
  • B: Add the localtime keyword to the service timestamps log datetimestatement
  • C: Add the mseckeyword to the service timestamps log datetimestatement.
  • D: Configure the router to be the NTP master.
  • E: Add the statement ntp broadcast to the NTP configuration of the neighboring router.








ProfExam
PROFEXAM WITH A 20% DISCOUNT

You can buy ProfExam with a 20% discount..

Get Now!


HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen



HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset