Download Designing Cisco Enterprise Networks (300-420 ENSLD).braindumps.300-420.2020-10-05.1e.86q.vcex


Download Exam

File Info

Exam Designing Cisco Enterprise Networks (300-420 ENSLD)
Number 300-420
File Name Designing Cisco Enterprise Networks (300-420 ENSLD).braindumps.300-420.2020-10-05.1e.86q.vcex
Size 3.9 Mb
Posted October 05, 2020
Downloads 17



How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Purchase
Coupon: EXAMFILESCOM

Coupon: EXAMFILESCOM
With discount: 20%


 
 



Demo Questions

Question 1
What command would display a single line of information for each virtual gateway or virtual forwarder on a switch?

  • A: switch# show glbp
  • B: switch# show glbp brief
  • C: switch# show standby
  • D: switch# show standby brief



Question 2
Which command enables GLBP on an interface?

  • A: glbp
  • B: glbp 10 ip 192.168.1.1
  • C: standby mode glbp
  • D: switchport mode glbp



Question 3
What command disables 802.1x authentication on a port and permits traffic without authentication?

  • A: dot1x port-control disable
  • B: dot1x port-control force-unauthorized
  • C: dot1x port-control auto
  • D: dot1x port-control force-authorized



Question 4
What command would be used to display detailed information regarding VRRP groups on the switch?

  • A: switch# show vrrp
  • B: switch# show standby
  • C: switch# show vrrp detail
  • D: switch# show standby detail



Question 5
Assuming that preempt is not configured, when does a router in an HSRP group assume the role of the active router for the group?

  • A: A router in standby status will become the active router if it has a higher priority than the active router.
  • B: A router in standby status will become the active router when it does not detect three consecutive hello messages from the active router.
  • C: A router in standby status will become the active router when it does not detect any hello messages from the active router within the configured holdtime.
  • D: A router in listening status will become the active router when it does not detect any hello messages from the active router within the configured holdtime.



Question 6
You have configured three routers in HSRP group 10 to provide gateway redundancy for VLAN 56. Your intention was for Router 1 to be the active router in the group and for Router 3 to be the standby router. Furthermore, in the event that Router 1 became unavailable, resulting in Router 3 becoming active, you intended for Router 1 to resume its role as active when it came back online. However, you discover that in practice, Router 1 does NOT resume the active role when it comes back online.
What command should be executed on Router 1?

  • A: router1(config)# interface VLAN 56router1(config-if)# standby 10 preempt
  • B: router1(config)# interface VLAN 10router1(config-if)# standby 56 preempt
  • C: router1(config)# standby 10 preempt
  • D: router1(config)# standby 56 preempt



Question 7
The partial output displayed in the exhibit is a result of what IOS command? (Click on the Exhibit(s) button.)
 


  • A: switch# show running-config
  • B: switch# show standby vlan1 active brief
  • C: switch# show hsrp 1
  • D: switch# show standby



Question 8
You have been assigned to create a plan to implement HSRP on the router connecting your company's network to the Internet. The router should be the active router in the HSRP group. On the active router, the following conditions should be met:
Enable preemption with no delay
Set Hello timer to 10 seconds and hold time to 25 seconds 
Set the priority to 150
Which of the following commands should be included in the plan to meet the given requirements? (Choose all that apply.)

  • A: standby 1 preempt delay minimum 10
  • B: standby 1 preempt
  • C: standby 1 priority 150
  • D: standby 1 timers 10 25
  • E: standby 1 timers 25 10
  • F: standby track interface S0/1



Question 9
Which statement best describes the function of Hot Standby Router Protocol (HSRP)?

  • A: HSRP specifies a single IP address that all routers in the group must use.
  • B: HSRP defines a set of routers that represent one virtual, fault-tolerant router.
  • C: HSRP provides a round-robin gateway selection process to increase fault tolerance.
  • D: HSRP defines a frame-tagging scheme that allows end stations to use any router as a gateway.



Question 10
Which of the following statements best describes the result of issuing the command standby 44 timers 3 1 on an HSRP router?

  • A: The holdtime will be set to a value of 3, and the hellotime will be set to a value of 1.
  • B: The status of the standby router will be displayed as unknown expired.
  • C: The role of active router will be passed repeatedly from one router to another.
  • D: The router will be configured to reassume the role of active router in the event that the router fails and is subsequently restarted.








ProfExam
PROFEXAM WITH A 20% DISCOUNT

You can buy ProfExam with a 20% discount..

Get Now!


HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen



HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset