Download Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI).braindumps.300-410.2020-03-27.1e.35q.vcex

Download Exam

File Info

Exam Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI)
Number 300-410
File Name Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI).braindumps.300-410.2020-03-27.1e.35q.vcex
Size 2.84 Mb
Posted March 27, 2020
Downloads 93

How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.


With discount: 20%


Demo Questions

Question 1
R2 has a locally originated prefix and has these configurations:


What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 ( by using the neighbor route-map OUT out command?

  • A: R1 sees as two AS hops away instead of one AS hop away.
  • B: R1 does not accept any routes other than
  • C: R1 does not forward traffic that is destined for
  • D: Network is not allowed in the R1 table

Question 2
Which method changes the forwarding decision that a router makes without first changing the routing table or influencing the IP data plane?

  • A: nonbroadcast multiaccess
  • B: packet switching
  • C: policy-based routing
  • D: forwarding information base

Question 3
Refer to the exhibit. The output of the trace route from R5 shows a loop in the network. Which configuration prevents this loop? 


  • A:
  • B:
  • C:
  • D:

Question 4
Refer to the exhibit. An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next hop is chosen. What is the reason for this? 


  • A: Dynamic routing protocols always have priority over static routes.
  • B: The metric of the OSPF route is lower than the metric of the static route.
  • C: The configured AD for the static route is higher than the AD of OSPF.
  • D: The syntax of the static route is not valid, so the route is not considered.

Question 5
Refer to the exhibit. An engineer is trying to generate a summary route in OSPF for network, but the summary route does not show up in the routing table. Why is the summary route missing? 


  • A: The summary-address command is used only for summarizing prefixes between areas.
  • B: The summary route is visible only in the OSPF database, not in the routing table.
  • C: There is no route for a subnet inside, so the summary route is not generated.
  • D: The summary route is not visible on this router, but it is visible on other OSPF routers in the same area.

Question 6
Refer to the exhibit. An engineer is trying to block the route to from the routing table by using the configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route? 


  • A: Use an extended access list instead of a standard access list.
  • B: Change sequence 10 in the route-map command from permit to deny.
  • C: Use a prefix list instead of an access list in the route map.
  • D: Add this statement to the route map: route-map RM-OSPF-DL deny 20.

Question 7
What is a prerequisite for configuring BFD?

  • A: Jumbo frame support must be configured on the router that is using BFD.
  • B: All routers in the path between two BFD endpoints must have BFD enabled.
  • C: Cisco Express Forwarding must be enabled on all participating BFD endpoints.
  • D: To use BFD with BGP, the timers 3 9 command must first be configured in the BGP routing process.

Question 8
Refer to the exhibit. R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to from R1, but it does not advertise to R3. What is the reason the route is not advertised? 


  • A: R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients.
  • B: Route reflector setup requires full IBGP mesh between the routers.
  • C: In route reflector setup, only classful prefixes are advertised to other clients.
  • D: In route reflector setups, prefixes are not advertised from one client to another.

Question 9

Refer to the exhibit. In which circumstance does the BGP neighbor remain in the idle condition?

  • A: if prefixes are not received from the BGP peer
  • B: if prefixes reach the maximum limit
  • C: if a prefix list is applied on the inbound direction
  • D: if prefixes exceed the maximum limit

Question 10
Which attribute eliminates LFAs that belong to protected paths in situations where links in a network are connected through a common fiber?

  • A: shared risk link group-disjoint
  • B: linecard-disjoint
  • C: lowest-repair-path-metric
  • D: interface-disjoint


You can buy ProfExam with a 20% discount..

Get Now!


Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen


Use VCE Exam Simulator to open VCE files