Download Designing Cisco Wireless Enterprise Networks.test4prep.300-360.2020-02-19.1e.131q.vcex

Download Exam

File Info

Exam Designing Cisco Wireless Enterprise Networks
Number 300-360
File Name Designing Cisco Wireless Enterprise Networks.test4prep.300-360.2020-02-19.1e.131q.vcex
Size 1.58 Mb
Posted February 19, 2020
Downloads 17

How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.


With discount: 20%


Demo Questions

Question 1
Which two types of information must be included in the installation inventory portion of the post-installation report? (Choose two.)

  • A: all AP, controller, and MSE administrator credentials
  • B: the names, locations, IP addresses, MAC addresses, etc. for every AP, controller, and MSE in the WLAN
  • C: a layout of the rack that the equipment is installed
  • D: results of the coverage audit performed with the site survey mapping tool
  • E: the number and type of all WLAN clients and tags

Question 2
A customer wants to implement a wireless network in a historic location, but is concerned about the structural and aesthetic impact to the facility. Which benefit of using wireless mesh addresses these concerns?

  • A: PoE is required only at the installation location.
  • B: The APs do not have LED lights.
  • C: More wireless channels can be supported.
  • D: APs do not need network connections.

Question 3
A customer has restricted the AP and antenna combinations for a design to be limited to one model integrated antenna AP for carpeted spaces and one model external antenna AP, with high gain antennas for industrial, maintenance, or storage areas. When moving between a carpeted area to an industrial area, the engineer forgets to change survey devices and surveys several APs. Which option is the best to reduce the negative impact of the design?

  • A: Deploy the specified access points per area type.
  • B: Resurvey and adjust the design.
  • C: Increase the Tx power on incorrectly surveyed access points.
  • D: Deploy unsurveyed access points to the design.

Question 4
A customer has dual-band devices that they want to use 40 MHz channels. If the customer is using Cisco 3600 Series access points with a 5508 controller. Which setting assists with this change?

  • A: Enable band select globally.
  • B: Enable aggressive load balancing.
  • C: Disable lower data rates on 802 .11G GHz radios.
  • D: Disable overlapping 802.11G channels.

Question 5
An engineer is assigned to assist a customer by estimating the number of access points needed to provide voice-grade wireless coverage in a carpeted office space. How many access points should be estimated to cover this space of roughly 38,000 square feet?

  • A: 17
  • B: 10
  • C: 6
  • D: 13

Question 6
An engineer plugs in a Cisco Aironet 2700 Series Access Point and it is running in low power. Which three power requirements should be verified? (Choose three.)

  • A: 802.3ac compliant
  • B: 802.3at compliant
  • C: AP requires 43 VDC to function in full power.
  • D: AIR-PWRINJ3 power injector should be used.
  • E: AP requires 57 VDC to function in full power.
  • F: AIR-PWRINJ4 power injector should be used.

Question 7
As part of a wireless site survey in a hospital, an engineer needs to identify potential Layer 1 interferers. In which three areas is the engineer most likely expect to find sources of 2.4 GHz and 5 GHz RF noise? (Choose three.)

  • A: emergency room
  • B: magnetic resonance imaging
  • C: laboratory
  • D: X-ray radiography
  • E: Gamma Knife radiation treatment
  • F: kitchen

Question 8
A Cisco 7925 phone at a client’s location is not registering with CUCM. The engineer analyzes a packet capture, sees that the phone receives an IP, and downloads the proper configuration file from TFTP successfully. What type of messages should the phone be sending at this point?

  • A: H.245
  • B: H.323
  • C: MCGP
  • D: SCCP

Question 9
What are two advantages of conducting an active survey versus a passive survey when verifying RF coverage? (Choose two.)

  • A: verifies packet loss
  • B: verifies roaming
  • C: verifies SNR
  • D: verifies signal level
  • E: verifies interferers

Question 10
An engineer is determining the signal levels for the wireless cells. Which signal-to-noise ratio is an optimal configuration to achieve?

  • A: minimum SNR of -33 dBm
  • B: minimum SNR of -25 dBm
  • C: minimum SNR of 25 dB
  • D: minimum SNR of 33 dB


You can buy ProfExam with a 20% discount..

Get Now!


Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen


Use VCE Exam Simulator to open VCE files