Download Designing Cisco Wireless Enterprise Networks.passguide.300-360.2018-09-08.1e.101q.vcex

Download Dump

File Info

Exam Designing Cisco Wireless Enterprise Networks
Number 300-360
File Name Designing Cisco Wireless Enterprise Networks.passguide.300-360.2018-09-08.1e.101q.vcex
Size 1015 Kb
Posted September 13, 2018
Downloaded 4



How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Purchase
Coupon: EXAMFILESCOM

Coupon: EXAMFILESCOM
With discount: 20%





Demo Questions

Question 1
When designing a WLAN, AP placement is important. Which option describes how to rank the density of APs needed to support location services versus data and voice services?

  • A: Data services have the lowest density of APs compared to location services, which has the highest density.
  • B: Data services have a lower density of APs compared to location services, but more than voice.
  • C: Voice services have the highest density of APs over location and data services.
  • D: Voice and data services require a higher density of APs than location services.



Question 2
You have a customer that is building a new campus of four 3-story buildings that you have just completed the site survey for. The customer is interested in the mount of rack space they will need to allocate in either the building MDF or in the data center for controllers. Each building is going to require 75 APs to support voice and data. How should the controllers be deployed to provide the least number of controllers, the highest redundancy, and the easiest management?

  • A: Use the centralized deployment method in the data center with the N + N redundancy method.
  • B: Use the centralized deployment method in the data center with the N + 1 redundancy method
  • C: Use the centralized deployment method in the data center with the 1 + 1 redundancy method and client SSO.
  • D: Use the distributed deployment method in each building MDF with the N + 1 redundancy method.
  • E: Use the distributed deployment method in each building MDF with the N + N + 1 redundancy method.
  • F: Use the distributed deployment method in each building MDF with the N + N redundancy method.



Question 3
After the completion of a site survey with Ekahau Site Survey tool, using the default color palette, it is noted that multiple areas are shown as white on the heat map when viewing 5 GHz signal strength data. What does this indicate about the signal strength?

  • A: The area is below the minimum threshold configured on the tool.
  • B: The area is below the detectable level and indicates no RF signal.
  • C: The area is below -100 dBm at coverage cell edge.
  • D: The area is below -67 dBm at coverage cell edge.



Question 4
A customer has deployed an N+N redundant wireless infrastructure. In this deployment, the access points have been salt and peppered between controllers. 
What configuration would be necessary to cut down on the use of mobility tunnels for voice clients?

  • A: mobility anchor
  • B: KIS based CAC
  • C: media session snooping
  • D: re-anchor roamed voice clients



Question 5
An engineer is assigned to provide wireless coverage in a provincial capital building. Due to the age and historic nature of the building, the ability to run new copper Ethernet cable to desired AP locations is limited. Which requirement should the engineer specify to overcome this restriction?

  • A: Deploy access points where the survey indicates and connect them via fiber optic cable, using a media adapter, and locally provide power.
  • B: Deploy access points to each phone location converting two spare pairs of copper from the phone line to Ethernet and locally provide power.
  • C: Deploy access point devices where limited cable can be run or exists and connect high-gain antennas and increase Tx power to increase cell size.
  • D: Deploy RAP where limited cable can be run or exists, and extend coverage using MAP.



Question 6
Which two steps are associated with the active portion of the audit when a post-installation audit is performed with an auditing tool such as Ekahau? (Choose two.)

  • A: Check for co-channel interference by standing near an access point on one channel and watching for other access points that are on the same channel.
  • B: Verify smooth roaming.
  • C: Check to see if the signal level on other access points that are heard on the same channel is at least 19 dBm weaker than the access point that you are next to.
  • D: Check that all channels are supported by the APs, regardless of client capabilities.
  • E: Verify that the network traffic of physical data rate and packet loss meets user requirements.



Question 7
A downstream packet that contains a DSCP value arrives at the WLC Ethernet interface from the wired source network. The WLC is configured for QoS WLAN 802.1p mapping. How does the WLC treat the CAPWAP QoS marking when leaving the controller interface for the respective AP and final wireless client destination?

  • A: No outer CAPWAP or inner QoS tagging is applied.
  • B: The outer CAPWAP CoS is marked and capped and the inner DSCP maintains the original marking.
  • C: No outer CAPWAP QoS tag is applied, but the original DSCP is maintained inside CAPWAP.
  • D: The outer CAPWAP DHCP is marked and capped without any inner DSCP value.



Question 8
An engineer is planning for a 24 Mbps data rate on the 5Ghz band for a new installation. 
What is the coverage area from the AP if the environment and other factors are not taken into consideration?

  • A: 225 feet
  • B: 80 feet
  • C: 150 feet
  • D: 100 feet



Question 9
A customer is deploying a mesh outdoor wireless network based on FCC standards where spectrum analysis shows significant radar energy propagating throughout the coverage area from a local weather station. Which channel must be excluded from the access points RRM calculation to avoid network disruption due to weather radar activity?

  • A: 132
  • B: 44
  • C: 11
  • D: 36



Question 10
An engineer installed a 3702 AP and is getting power from the switch. What is the reason for getting 3x3 MIMO instead of 4x4?

  • A: 802.1p
  • B: 802.3af
  • C: 802.11e
  • D: 802.3at









CONNECT US


ProfExam
PROFEXAM WITH A 20% DISCOUNT

You can buy ProfExam with a 20% discount..

Get Now!


HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen



HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset