Download Troubleshooting Cisco Data Center Infrastructure (DCIT).certkiller.300-180.2019-10-29.1e.125q.vcex

Download Dump

File Info

Exam Troubleshooting Cisco Data Center Infrastructure (DCIT)
Number 300-180
File Name Troubleshooting Cisco Data Center Infrastructure (DCIT).certkiller.300-180.2019-10-29.1e.125q.vcex
Size 5.38 Mb
Posted October 29, 2019



How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Purchase
Coupon: EXAMFILESCOM

Coupon: EXAMFILESCOM
With discount: 20%





Demo Questions

Question 1
FHRP isolation between data center networks that are connected over an OTV network is a two-step process; the first prevents FHRP peering by filtering FHRP control packets across the overlay via a VLAN ACL. 
What is the second step?

  • A: Filter the FHRP MAC addresses that are being advertised by IS-IS.
  • B: Disable the auto-population of the OTV MAC address table.
  • C: Apply a VLAN to a route map that is applied to the OTV routing process.
  • D: Remove the FHRP VLAN from the OTV exatend-vlan list.



Question 2
One of your Cisco Nexus Series interfaces has become errdisabled with the error message “DCX-No ACK in 100 PDUs”. 
How often are these acknowledgements exchanged?

  • A: 30 seconds
  • B: 15 seconds
  • C: 45 seconds
  • D: 60 seconds



Question 3
A customer is trying to boot an operating system installed on a Cisco UCS B-Series blade server after a RAID1 cluster migration. The RAID LUN remains in inactive state during and after the service profile association and the server does not boot. 
What is the cause of this problem?

  • A: The server needs to be booted via SAN in cluster migration to support RAID1.
  • B: The local disk configuration policy in the service profile on the server is configured with Any Configuration mode rather than RAID1.
  • C: RAID1 is not supported in cluster migration mode on a Cisco UCS B-Series blade server.
  • D: The Cisco UCS B-Series blade server has older firmware that needs to be updated first.



Question 4
View the Exhibit. 

  

Refer to the exhibit. When your customers have NPV problems, which two actions should you take? (Choose two.)

  • A: Ensure that the VSAN value that is configured on the device link is correct.
  • B: For all the device links, ensure that the port mode on the NPV device is in Full_port mode.
  • C: Verify that the NPV core switch supports NPIV and that it is enabled.
  • D: Verify the status of the servers and external interfaces, using the show npv server status command.
  • E: Ensure that the VLAN values are configured on both sides of the NPV core switch.



Question 5
View the Exhibit. 

  

Refer to the exhibit. You have a server that fails to boot. 
Which option is a possible cause of the issue?

  • A: an incorrect boot policy
  • B: an incorrect FC/FCoE target port in the SAN
  • C: incorrect zoning
  • D: incorrect LUN masking on the storage array



Question 6
Which statement is true about the show cfs merge status name command?

  • A: In a successful merge, all switches are shown in a local fabric.
  • B: The merge master is selected based on the highest sWWN in the fabric.
  • C: The command shows the complete Cisco Fabric Services region database.
  • D: In a successful merge, all switches in the fabric are shown separately.



Question 7
Which two options are Cisco UCS default user roles? (Choose two.)

  • A: Server Resource Administrator
  • B: Administrator
  • C: Server Equipment Administrator
  • D: LAN Administrator
  • E: FCoE Administrator



Question 8
A Cisco Nexus 7010 Switch that is at the core of a customer network has high CPU utilization. 
What can the customer do to prevent a network outage and identify why CPU utilization is high?

  • A: use HSRP and vPC for redundancy to handle high CPU utilization
  • B: use the show process cpu command to see the high CPU utilization
  • C: apply a rate limit on the interfaces with high traffic
  • D: use CoPP



Question 9
View the Exhibit. 

  

Refer the exhibit. Which of these is an extension of the virtual machine abstraction that is applied to physical servers?

  • A: organization profile
  • B: compute profile
  • C: service profile
  • D: locale profile



Question 10
You see incoming updates in the logs from the hypervisor, but the state of the Cisco APIC fails to change. 
Which option is a possible cause of the issue?

  • A: No uplinks are configured on the Cisco AVS.
  • B: The VMM credentials are incorrect.
  • C: VMM is not integrated properly.
  • D: The APIC is in a minority state.









CONNECT US


ProfExam
PROFEXAM WITH A 20% DISCOUNT

You can buy ProfExam with a 20% discount..

Get Now!


HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen



HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset