Download Cisco.CertDumps.300-180.2017-12-07.1e.75q.vcex

File Info

Exam	Troubleshooting Cisco Data Center Infrastructure (DCIT)
Number	300-180
File Name	Cisco.CertDumps.300-180.2017-12-07.1e.75q.vcex
Size	2.36 Mb
Posted	December 07, 2017
Downloads	35

How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Download
ProfExam Simulator

Purchase
Coupon: EXAMFILESCOM

Coupon: EXAMFILESCOM
With discount: 20%

Demo Questions

Question 1

On a Cisco Nexus 5500 Series Switch, the VFC is stuck in the initializing state.
Which QoS statements must be configured for FCoE to operate?
A )

B )

C. )

D )

A: Option A
B: Option B
C: Option C
D: Option D

Correct Answer: D

Question 2

You plan to troubleshoot EPG communication by using atomic counters.
What do you consider before using the atomic counters?

A: Atomic counters only work properly in a transit, non-full-mesh topology.
B: Atomic counters also count spine proxy traffic.
C: Atomic counters do not count the traffic between EPGs that reside in different VRFs.
D: Atomic counters count the traffic for the endpoints that are located in different VRFs.

Correct Answer: C

Question 3

Which option describes why the service profiles do not inherit changes from the template?

A: It is an initial template.
B: The service profile is not compatible with the changes.
C: The service profile has disabled inheritance.
D: The changes to the template have not been committed.

Correct Answer: A

Question 4

FHRP isolation between data center networks that are connected over an OTV network is a two-step process; the first prevents FHRP peering by filtering FHRP control packets across the overlay via a VLAN ACL.
What is the second step?

A: Filter the FHRP MAC addresses that are being advertised by IS-IS.
B: Disable the auto-population of the OTV MAC address table.
C: Apply a VLAN to a route map that is applied to the OTV routing process.
D: Remove the FHRP VLAN from the OTV exatend-vlan list.

Correct Answer: A

Question 5

One of your Cisco Nexus Series interfaces has become errdisabled with the error message “DCX-No ACK in 100 PDUs”.
How often are these acknowledgements exchanged?

A: 30 seconds
B: 15 seconds
C: 45 seconds
D: 60 seconds

Correct Answer: A

Question 6

A customer is trying to boot an operating system installed on a Cisco UCS B-Series blade server after a RAID1 cluster migration. The RAID LUN remains in inactive state during and after the service profile association and the server does not boot.
What is the cause of this problem?

A: The server needs to be booted via SAN in cluster migration to support RAID1.
B: The local disk configuration policy in the service profile on the server is configured with Any Configuration mode rather than RAID1.
C: RAID1 is not supported in cluster migration mode on a Cisco UCS B-Series blade server.
D: The Cisco UCS B-Series blade server has older firmware that needs to be updated first.

Correct Answer: B

Question 7

View the Exhibit.

Refer to the exhibit. When your customers have NPV problems, which two actions should you take? (Choose two.)

A: Ensure that the VSAN value that is configured on the device link is correct.
B: For all the device links, ensure that the port mode on the NPV device is in Full_port mode.
C: Verify that the NPV core switch supports NPIV and that it is enabled.
D: Verify the status of the servers and external interfaces, using the show npv server status command.
E: Ensure that the VLAN values are configured on both sides of the NPV core switch.