Download Cisco.CertDumps.300-135.2017-10-07.17e.65q.vcex

Download Dump

File Info

Exam Troubleshooting and Maintaining Cisco IP Networks (TSHOOT v2.0)
Number 300-135
File Name Cisco.CertDumps.300-135.2017-10-07.17e.65q.vcex
Size 11.28 Mb
Posted July 24, 2018
Downloaded 9



How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Purchase
Coupon: EXAMFILESCOM

Coupon: EXAMFILESCOM
With discount: 20%





Demo Questions

Question 1
The implementations group has been using the test bed to do a `proof-of-concept' that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. 
Use the supported commands to isolated the cause of this fault and answer the following questions. 
What is the solution to the fault condition?

  • A: R1
  • B: R2
  • C: R3
  • D: R4
  • E: DSW1
  • F: DSW2
  • G: ASW1
  • H: ASW2



Question 2
The implementations group has been using the test bed to do a ,,proof-of-concept that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. 
Use the supported commands to isolated the cause of this fault and answer the following questions. 
The fault condition is related to switch technology?

  • A: NTP
  • B: Switch-to-Switch Connectivity
  • C: Loop Prevention
  • D: Access Vlans
  • E: VLAN ACL Port ACL
  • F: Switch Virtual Interface
  • G: Port Security



Question 3
The implementations group has been using the test bed to do a `proof-of-concept' that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. 
Use the supported commands to isolated the cause of this fault and answer the following questions. 
What is the solution to the fault condition?

  • A: In Configuration mode, using the interface range Fastethernet 1/0/1  2, then switchport mode access vlan 10 command.
  • B: In Configuration mode, using the interface range Fastethernet 1/0/1  2, then switchport access mode vlan 10 command.
  • C: In Configuration mode, using the interface range Fastethernet 1/0/1  2, then switchportvlan 10 access command.
  • D: In Configuration mode, using the interface range Fastethernet 1/0/1  2, then switchport access vlan 10 command.



Question 4
Exhibit:

 
   

A network administrator is troubleshooting an EIGRP connection between RouterA, IP address 10.1.2.1, andRouterB, IP address 10.1.2.2. Given the debug output on RouterA, which two statements are true? (Choose two.)

  • A: RouterA received a hello packet with mismatched autonomous system numbers.
  • B: RouterA received a hello packet with mismatched hello timers.
  • C: RouterA received a hello packet with mismatched authentication parameters.
  • D: RouterA received a hello packet with mismatched metric-calculation mechanisms.
  • E: RouterA will form an adjacency with RouterB.
  • F: RouterA will not form an adjacency with RouterB.



Question 5
When troubleshooting an EIGRP connectivity problem, you notice that two connected EIGRP routers are not becoming EIGRP neighbors. A ping between the two routers was successful. What is the next thing that should be checked?

  • A: Verify that the EIGRP hello and hold timers match exactly.
  • B: Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP peer command.
  • C: Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP traffic command.
  • D: Verify that EIGRP is enabled for the appropriate networks on the local and neighboring router.



Question 6
Refer to the exhibit. 

 
   

How would you confirm on R1 that load balancing is actually occurring on the default-network (0.0.0.0)?

  • A: Use ping and the show ip route command to confirm the timers for each default network resets to 0.
  • B: Load balancing does not occur over default networks; the second route will only be used for failover.
  • C: Use an extended ping along with repeated show ip route commands to confirm the gateway of last resort address toggles back and forth.
  • D: Use the traceroute command to an address that is not explicitly in the routing table.



Question 7
Which IPsec mode will encrypt a GRE tunnel to provide multiprotocol support and reduced overhead?

  • A: 3DES
  • B: multipoint GRE
  • C: tunnel
  • D: transport



Question 8
Which three features are benefits of using GRE tunnels in conjunction with IPsec for building site-to-site VPNs? (Choose three.)

  • A: allows dynamic routing over the tunnel
  • B: supports multi-protocol (non-IP) traffic over the tunnel
  • C: reduces IPsec headers overhead since tunnel mode is used
  • D: simplifies the ACL used in the crypto map
  • E: uses Virtual Tunnel Interface (VTI) to simplify the IPsec VPN configuration



Question 9
Which statement is true about an IPsec/GRE tunnel?

  • A: The GRE tunnel source and destination addresses are specified within the IPsec transform set.
  • B: An IPsec/GRE tunnel must use IPsec tunnel mode.
  • C: GRE encapsulation occurs before the IPsec encryption process.
  • D: Crypto map ACL is not needed to match which traffic will be protected.



Question 10
A customer network engineer has made configuration changes that have resulted in some loss of connectivity. You have been called in to evaluate a switch network and suggest resolutions to the problems. 

 
   

 
   

 
   

 
   

 
   
 
PC2 in VLAN 200 is unable to ping the gateway address 172.16.200.1; identify the issue.

  • A: VTP domain name mismatch on SW4
  • B: VLAN 200 not configured on SW1
  • C: VLAN 200 not configured on SW2
  • D: VLAN 200 not configured on SW4









CONNECT US


ProfExam
PROFEXAM WITH A 20% DISCOUNT

You can buy ProfExam with a 20% discount..

Get Now!


HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen



HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset