Download Implementing Cisco IP Switched Networks (SWITCH v2-0).passit4sure.300-115.2018-11-15.1e.445q.vcex

Download Dump

File Info

Exam Implementing Cisco IP Switched Networks (SWITCH v2.0)
Number 300-115
File Name Implementing Cisco IP Switched Networks (SWITCH v2-0).passit4sure.300-115.2018-11-15.1e.445q.vcex
Size 10.69 Mb
Posted November 15, 2018
Downloads 97



How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Purchase
Coupon: EXAMFILESCOM

Coupon: EXAMFILESCOM
With discount: 20%





Demo Questions

Question 1
Instructions 
Enter IOS commands on the device to verify network operation and answer the multiple-choice questions. 
THIS TASK DOES NOT REQUIRE DEVICE CONFIGURATION. 
Click on SW1, SW2, New_Switch or SW4 to gain access to the consoles of these devices. No console or enable passwords are required. 
To access the multiple-choice questions, click on the numbered boxes on the left of the top panel. 
There are four multiple-choice questions with this task. Be sure to answer all four questions before selecting the Next button 
Scenario 
You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration. 
Topology 

  

  

  

  

  

You are adding new VLANs. VLAN500 and VLAN600 to the topology in such way that you need to configure SW1 as primary root for VLAN 500 and secondary for VLAN 600 and SW2 as primary root for VLAN 600 and secondary for VLAN 500. Which configuration step is valid?

  • A: Configure VLAN 500 & VLAN 600 on both SW1 & SW2
  • B: Configure VLAN 500 and VLAN 600 on SW1 only
  • C: Configure VLAN 500 and VLAN 600 on SW2 only
  • D: Configure VLAN 500 and VLAN 600 on SW1, SW2 and SW4
  • E: On SW2; configure vtp mode as off and configure VLAN 500 and VLAN 600; configure back to vtp server mode.



Question 2
Instructions 
Enter IOS commands on the device to verify network operation and answer the multiple-choice questions. 
THIS TASK DOES NOT REQUIRE DEVICE CONFIGURATION. 
Click on SW1, SW2, New_Switch or SW4 to gain access to the consoles of these devices. No console or enable passwords are required. 
To access the multiple-choice questions, click on the numbered boxes on the left of the top panel. 
There are four multiple-choice questions with this task. Be sure to answer all four questions before selecting the Next button 
Scenario 
You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration. 
Topology 

  

  

  

  

  

Examine the VTP configuration. You are required to configure private VLANs for a new server deployment connecting to the SW4 switch. 
Which of the following configuration steps will allow creating private VLANs?

  • A: Disable VTP pruning on SW1 only
  • B: Disable VTP pruning on SW2 only
  • C: Disable VTP pruning on SW4 only
  • D: Disable VTP pruning on SW2, SW4 and New_Switch
  • E: Disable VTP pruning on New_Switch and SW4 only.



Question 3
Which command sets the interval at which a device sends LLDP updates to its neighbors?

  • A: lldp transmit
  • B: lldp timer
  • C: lldp holdtime
  • D: lldp tlv-select



Question 4
Which two statements about RPVST+ are true? (Choose two.)

  • A: It is incompatible with spanning-tree PortFast.
  • B: It supports two STP instances per VLAN.
  • C: It requires approximately 50 seconds to complete reconvergence.
  • D: Backwards compatibility with 802.1d is not supported.
  • E: It elects one root switch per VLAN instance.
  • F: It automatically enables UplinkFast and BackboneFast.



Question 5
Which statement is true when UDLD is configured on a link and the link is determined to be unidirectional?

  • A: The port remains up for a configured time interval and then error disables if the link remains unidirectional.
  • B: LLDP is enabled on the port.
  • C: The port sends a log message to the console.
  • D: The port is disabled immediately.



Question 6
Which command enables PortFast and disables port channel on a physical interface?

  • A: switchport host
  • B: switchport mode access
  • C: spanning-tree portfast
  • D: switchport mode dynamic auto



Question 7
Under which two conditions does Cisco StackWise Virtual transmit data over a virtual link? (Choose two.)

  • A: Packets are processed on the egress interface on the active switch.
  • B: Packets are processed on the ingress interface on the active switch.
  • C: Packets are processed on the egress interface on the standby switch.
  • D: Packets are processed on the ingress interface on the standby switch.
  • E: A VLAN is flooded over Layer 2.



Question 8
  

Refer to the exhibit. You have applied this configuration to Switches A, B, C and D, and the switches are connected to one another on access ports. Which two additional actions must you take to enable the hosts on VLAN 3 to communicate with one another considering future growth with hosts on additional VLANs? (Choose two.)

  • A: Assign VLAN 3 to the ports connecting to the hosts.
  • B: Reconfigure the access ports connecting the switches as trunk ports.
  • C: Configure VLAN 3 as an SVI with a working IP address.
  • D: Configure VTP transparent mode to allow hosts with additional VLANs.
  • E: Configure VLAN 3 in VLAN database mode.



Question 9
  

Refer to the exhibit. Which effect of this configuration is true?

  • A: Traffic received on VLANs 10 and 12 only is copied and sent to interface g0/1.
  • B: Traffic sent on VLANs 10, 11, and 12 is copied and sent to interface g0/1.
  • C: Traffic sent on VLANs 10 and 12 is copied and sent to interface g0/1.
  • D: Traffic received on VLANs 10, 11 and 12 only is copied and sent to interface g0/1.



Question 10
Which two statements about Cisco StackWise are true? (Choose two.)

  • A: It supports multiple switches in a stack.
  • B: The LAN base feature set is supported on mixed stacks.
  • C: Stacks running the LAN base feature set support Layer 3 features.
  • D: Each stack identifies a stack master and a backup stack master.
  • E: It supports both homogeneous and mixed stacks.









CONNECT US


ProfExam
PROFEXAM WITH A 20% DISCOUNT

You can buy ProfExam with a 20% discount..

Get Now!


HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen



HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset