Download Implementing Cisco IP Routing (ROUTE v2-0).pass4sures.300-101.2018-08-04.1e.341q.vcex

Download Dump

File Info

Exam Implementing Cisco IP Routing (ROUTE v2.0)
Number 300-101
File Name Implementing Cisco IP Routing (ROUTE v2-0).pass4sures.300-101.2018-08-04.1e.341q.vcex
Size 13.84 Mb
Posted August 04, 2018
Downloaded 36



How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Purchase
Coupon: EXAMFILESCOM

Coupon: EXAMFILESCOM
With discount: 20%





Demo Questions

Question 1
After you review the output of the command show ipv6 interface brief, you see that several IPv6 addresses have the 16-bit hexadecimal value of "fFFE" inserted into the address. Based on this information, what do you conclude about these IPv6 addresses?

  • A: IEEE EUI-64 was implemented when assigning IPv6 addresses on the device.
  • B: The addresses were misconfigured and will not function as intended.
  • C: IPv6 addresses containing "FFFE" indicate that the address is reserved for multicast.
  • D: The IPv6 universal/local flag (bit 7) was flipped.
  • E: IPv6 unicast forwarding was enabled, but IPv6 Cisco Express Forwarding was disabled.



Question 2
A packet capture log indicates that several router solicitation messages were sent from a local host on the Ipv6 segment. What is the expected acknowledgment and its usage?

  • A: Router acknowledgment messages will be forwarded upstream, where the DHCP server will allocate addresses to the local host.
  • B: Routers on the Ipv6 segment will respond with an advertisement that provides an external path from the local subnet, as well as certain data, such as prefix discovery.
  • C: Duplicate Address Detection will determine if any other local host is using the same Ipv6 address for communication with the Ipv6 routers on the segment.
  • D: All local host traffic will be redirected to the router with the lowest ICMPv6 signature, which is statically defined by the network administrator.



Question 3
Route.com is a small IT corporation that is attempting to implement the network shown in the exhibit. Currently the implementation is partially completed. OSPF has been configured on routers Chicago and NewYork. The SO/O interface on Chicago and the SO/1 interface on NewYork are in Area 0. The loopbackO interface on NewYork is in Area 1. However, they cannot ping from the serial interface of the Seattle router to the loopback interface of the NewYork router. You have been asked to complete the implementation to allow this ping. 
ROUTE.com’s corporate implementation guidelines require:
The OSPF process ID for all routers must be 10. 
The routing protocol for each interface must be enabled under the routing process. 
The routing protocol must be enabled for each interface using the most specific wildcard mask possible. 
The serial link between Seattle and Chicago must be in OSPF area 21. 
OSPF area 21 must not receive any inter-area or external routes. 
Network Information 
Seattle 
S0/0 192.168.16.5/30 — Link between Seattle and Chicago 
Secret Password: cisco
Chicago 
S0/0 192.168.54.9/30 — Link between Chicago and New York 
S0/1 192.168.16.6/30 — Link between Seattle and Chicago 
Secret Password: cisco
New York 
S0/1 192.168.54.10/30 — Link between Chicago and New York 
Loopback0 172.16.189.189 
Secret Password: cisco

  

  

  

  

  • A: See explanation below



Question 4
JS Industries has expanded their business with the addition of their first remote office. The remote office router (R3) was previously configured and all corporate subnets were reachable from R3. JS Industries is interested in using route summarization along with the EIGRP Stub Routing feature to increase network stability while reducing the memory usage and bandwidth utilization to R3. Another network professional was tasked with implementing this solution. However, in the process of configuring EIGRP stub routing connectivity with the remote network devices off of R3 has been lost. 
Currently EIGRP is configured on all routers R2, R3, and R4 in the network. Your task is to identify and resolve the cause of connectivity failure with the remote office router R3. Once the issue has been resolved you should complete the task by configuring route summarization only to the remote office router R3. 
You have corrected the fault when pings from R2 to the R3 LAN interface are successful, and the R3 IP routing table only contains 2 10.0.0.0 subnets. 

  

  

  

  

  • A: See explanation below



Question 5
ROUTE.com is a small IT corporation that has an existing enterprise network that is running Ipv6 0SPFv3. Currently OSPF is configured on all routers. However, R4’s loopback address (FEC0:4:4) cannot be seen in R1’s Ipv6 routing table. You are tasked with identifying the cause of this fault and implementing the needed corrective actions that uses OPSF features and does not change the current area assignments. You will know that you have corrected the fault when R4’s loopback address (FEC0:4:4) can be seen in RTs Ipv6 routing table.
Special Note: To gain the maximum number of points you must remove all incorrect or unneeded configuration statements related to this issue.

  

  

  

  

  

  • A: See explanation below



Question 6
You are a network engineer with ROUTE.com, a small IT company. ROUTE.com has two connections to the Internet; one via a frame relay link and one via an EoMPLS link. IT policy requires that all outbound HTTP traffic use the frame relay link when it is available. All other traffic may use either link. No static or default routing is allowed. 
Choose and configure the appropriate path selection feature to accomplish this task. You may use the Test Workstation to generate HTTP traffic to validate your solution. 

  

  

  

  • A: See explanation below



Question 7
You are a network engineer with ROUTE.com, a small IT company. They have recently merged two organizations and now need to merge their networks as shown in the topology exhibit. One network is using OSPF as its IGP and the other is using EIGRP as its IGP. R4 has been added to the existing OSPF network to provide the interconnect between the OSPF and EIGRP networks. Two links have been added that will provide redundancy. 
The network requirements state that you must be able to ping and telnet from loopback 101 on R1 to the OPSF domain test address of 172.16.1.100. All traffic must use the shortest path that provides the greatest bandwidth. The redundant paths from the OSPF network to the EIGRP network must be available in case of a link failure. No static or default routing is allowed in either network. 
A previous network engineer has started the merger implementation and has successfully assigned and verified all IP addressing and basic IGP routing. You have been tasked with completing the implementation and ensuring that the network requirements are met. You may not remove or change any of the configuration commands currently on any of the routers. You may add new commands or change default values. 

  

  • A: Please see explanation



Question 8
Scenario 
You have been asked to evaluate how EIGRP is functioning in a customer network. Access the device consoles to answer the questions. 
Instructions 
Enter IOS commands on the device to verify network operation and answer for multiple-choice questions. 
THIS TASK DOES NOT REQUIRE DEVICE CONFIGURATION. 
Click on the individual device icons or use the tab at the bottom of the screen to gain access to the console for each device. 
No console or enable passwords are required. 
To access the multiple-choice questions, click on the numbered boxes on the left of the top panel. 
There are four multiple-choice questions with this task. Be sure to answer all five questions before selecting the Next button. 

  

  

  

  

  

  

  

Traffic from R1 to R6’s Loopback address is load shared between R1-R2-R4-R6 and R1-R3-R5-R6 paths. What is the ratio of traffic over each path?

  • A: 1:1
  • B: 1:5
  • C: 6:8
  • D: 19:80



Question 9
Scenario 
You have been asked to evaluate how EIGRP is functioning in a customer network. Access the device consoles to answer the questions. 
Instructions 
Enter IOS commands on the device to verify network operation and answer for multiple-choice questions. 
THIS TASK DOES NOT REQUIRE DEVICE CONFIGURATION. 
Click on the individual device icons or use the tab at the bottom of the screen to gain access to the console for each device. 
No console or enable passwords are required. 
To access the multiple-choice questions, click on the numbered boxes on the left of the top panel. 
There are four multiple-choice questions with this task. Be sure to answer all five questions before selecting the Next button. 

  

  

  

  

  

  

  

What type of route filtering is occurring on R6?

  • A: Distribute-list using an ACL
  • B: Distribute-list using a prefix-list
  • C: Distribute-list using a route-map
  • D: An ACL using a distance of 255



Question 10
Scenario 
You have been asked to evaluate how EIGRP is functioning in a customer network. Access the device consoles to answer the questions. 
Instructions 
Enter IOS commands on the device to verify network operation and answer for multiple-choice questions. 
THIS TASK DOES NOT REQUIRE DEVICE CONFIGURATION. 
Click on the individual device icons or use the tab at the bottom of the screen to gain access to the console for each device. 
No console or enable passwords are required. 
To access the multiple-choice questions, click on the numbered boxes on the left of the top panel. 
There are four multiple-choice questions with this task. Be sure to answer all five questions before selecting the Next button. 
  

  

  

  

  

  

  

Which key chain is being used for authentication of EIGRP adjacency between R4 and R2?

  • A: CISCO
  • B: EIGRP
  • C: KEY
  • D: MD5









CONNECT US


ProfExam
PROFEXAM WITH A 20% DISCOUNT

You can buy ProfExam with a 20% discount..

Get Now!


HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen



HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset