Download Cisco.Certkiller.300-101.2017-09-25.1e.80q.vcex

Download Exam

File Info

Exam Implementing Cisco IP Routing (ROUTE v2.0)
Number 300-101
File Name Cisco.Certkiller.300-101.2017-09-25.1e.80q.vcex
Size 3.84 Mb
Posted September 25, 2017
Downloads 79

How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.


With discount: 20%


Demo Questions

Question 1
Examine the following output of the show ip ospf interface command. 
What would be the effect of executing the auto-cost reference bandwidth 2000 command on Router43 in router OSPF mode?

  • A: the cost of the Serial interface would increase to 20
  • B: the cost of the FastEthernet interfaces would increase to 2000
  • C: the cost of the Serial interface would increase to 647
  • D: the cost of the FastEthernet interfaces would increase to 20

Question 2
You instructed your assistant to configure redistribution of OSPF routes into EIGRP on Router 9. The routes are not being advertised to EIGRP and you are troubleshooting the problem. The EIGRP process ID is 100 and the OSPF process ID is 20. When you ask your assistant what commands were executed, you are shown the following:
Router9(config)# router eigrp 100 
Router9(config-router)# redistribute ospf 20 
What is the problem? 

  • A: no metric was configured
  • B: the process IDs are incorrect
  • C: the redistribute command is executed at the interface configuration prompt
  • D: the redistribute command is executed at the global configuration prompt

Question 3
Which command should be executed on all ABRs in an area to configure it as a totally stubby area?

  • A: Router(config-router)# area process-id stub [no-summary]
  • B: Router(config-router)# area area-id [no-summary] stub
  • C: Router(config-router)# area area-id stub [no-summary]
  • D: Router(config-ospf)# area router-id [no-summary] stub

Question 4
You have configured a BGP network with several routers in the same autonomous system (AS). There are three possible routes from router A to router B in the network. The following conditions exist:
All three routes have the same weight 
All three routes were originated locally through the use of the network command 
The bgp default local-preference 50 command is executed for all three routes 
All three routes have different lists of AS through which they travel  
Which of the following parameters is used to select the best path among the three routes?

  • A: Weight
  • B: MED
  • D: AS_Path

Question 5
Examine the exhibit by pressing the Exhibit(s) button. 

You are to configure R1 to belong to area 5. This area does not accept routes from the external AS or summary routes from any other internal areas. Refer to the IP addressing below. 
R1 - int E0 - 
R2 - int E0 - 
R2 - int E1 - 
R3 - int E0 - 
Which configuration commands are required to correctly configure R1?

  • A: R1(config)# router ospf 10 
    R1(config-router)# area 5 no-summary stub 
    R1(config-router)# network area 5
  • B: R1(config)# router ospf 5 
    R1(config-router)# area 5 stub 
    R1(config-router)# network area 5
  • C: R1(config)# router ospf 10 
    R1(config-router)# area 5 stub 
    R1(config-router)# network area 5 
  • D: R1(config)# router ospf 5 
    R1(config-router)# area 5 stub no-summary 
    R1(config-router)# network area 5

Question 6
Which of the following commands will display information about Type 4 LSAs?

  • A: show ip ospf database external
  • B: show ip ospf database asbr-summary
  • C: show ip ospf database summary
  • D: show ip ospf database router

Question 7
You have a router that is running both OSPF and RIP. You have configured this router to perform mutual redistribution between the two protocols. The following conditions exist:
The S0/0 interface, which is configured for RIP, is routing for the network. 
The S0/1 interface, which is configured for OSPF, is routing for the network.  
Users in the RIP domain are unable to connect to devices in the OSPF domain.  
What must be done to allow the OSPF routes to be redistributed into the RIP domain? (Choose two. Each correct answer is part of the solution.)

  • A: Create a static route that points to with a next hop of null0.
  • B: Execute the passive-interface command on S0/0.
  • C: Create a loopback address on the router
  • D: Redistribute static routes into RIP.

Question 8
You are the network administrator for a large software organization. You designed the LAN in the organization's main building for connecting the internal LAN to a 
WAN as shown below:

You have configured EIGRP with the variance parameter set to 3 on all the routers to enable unequal load balancing from the network to the WAN. The 
delay configured on each of the routers is shown in the LAN diagram, and the K values are set as follows:
K1 = 0 
K2 = 0 
K3 = 1 
K4 = 0 
K5 = 0 
Which of the following paths are entered into the routing tables as a result of the unequal load balancing configured on the routers? (Choose all that apply.)

  • D: RA-RC-RG-RJ-RK 

Question 9
OSPF area border routers (ABRs) advertise a default route to stub and totally stubby areas.  
Which command is the BEST command to configure a cost of 25 for the default route advertised to area 1?

  • A: Router(config-router)# area 1 cost 25
  • B: Router(config-router)# area 1 default 25
  • C: Router(config-router)# area 1 default-cost 25
  • D: Router(config-router)# area 1 default-route-cost 25

Question 10
You need to manually assign IPv6 addresses to the interfaces on an IPv6-enabled router. While assigning addresses, you need to ensure that the addresses participate in neighbor discovery and in stateless auto-configuration process on a physical link. 
Which of the following addresses can be assigned to the interfaces? 

  • A: FEC0:0:0:1::1/64 
  • B: FE80::260:3EFF:FE11:6770/10
  • C: 2001:0410:0:1:0:0:0:1/64
  • D: 2002:500E:2301:1:20D:BDFF:FE99:F559/64


You can buy ProfExam with a 20% discount..

Get Now!


Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen


Use VCE Exam Simulator to open VCE files