Download Cisco Certified Network Associate (200-301 CCNA).PremTest.200-301.2020-06-20.1e.99q.vcex

Download Exam

File Info

Exam Cisco Certified Network Associate (200-301 CCNA)
Number 200-301
File Name Cisco Certified Network Associate (200-301 CCNA).PremTest.200-301.2020-06-20.1e.99q.vcex
Size 3.77 Mb
Posted June 20, 2020
Downloads 51

How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.


With discount: 20%


Demo Questions

Question 1

Refer to the exhibit. Which prefix does Router1 use for traffic to Host A?

  • A:
  • B:
  • C:
  • D:

Question 2
Which command automatically generates an IPv6 address from a specified IPv6 prefix and MAC address of an interface?

  • A: ipv6 address dhcp
  • B: ipv6 address 2001:DB8:5:112::/64 eui-64
  • C: ipv6 address autoconfig
  • D: ipv6 address 2001:DB8:5:112::2/64 link-local

Question 3
When configuring IPv6 on an interface, which two IPv6 multicast groups are joined? (Choose two.)

  • A: 2000::/3
  • B: 2002::5
  • C: FC00::/7
  • D: FF02::1
  • E: FF02::2

Question 4
Which IPv6 address type provides communication between subnets and cannot route on the Internet?

  • A: link-local
  • B: unique local
  • C: multicast
  • D: global unicast

Question 5
What is a benefit of using a Cisco Wireless LAN Controller?

  • A: It eliminates the need to configure each access point individually.
  • B: Central AP management requires more complex configurations.
  • C: Unique SSIDs cannot use the same authentication method.
  • D: It supports autonomous and lightweight APs. 

Question 6
Which action is taken by switch port enabled for PoE power classification override?

  • A: If a monitored port exceeds the maximum administrative value for power, the port is shutdown and err-disabled.
  • B: When a powered device begins drawing power from a PoE switch port, a syslog message is generated.
  • C: As power usage on a PoE switch port is checked, data flow to the connected device is temporarily paused.
  • D: If a switch determines that a device is using less than the minimum configured power, it assumes the device has failed and disconnects it.

Question 7
Which action must be taken to assign a global unicast IPv6 address on an interface that is derived from the MAC address of that interface? 

  • A: explicitly assign a link-local address
  • B: disable the EUI-64 bit process
  • C: enable SLAAC on an interface
  • D: configure a stateful DHCPv6 server on the network

Question 8
Several new coverage cells are required to improve the Wi-Fi network of an organization. Which two standard designs are recommended? (Choose two.)

  • A: 5GHz provides increased network capacity with up to 23 nonoverlapping channels.
  • B: 5GHz channel selection requires an autonomous access point.
  • C: Cells that overlap one another are configured to use nonoverlapping channels.
  • D: Adjacent cells with overlapping channels use a repeater access point.
  • E: For maximum throughput, the WLC is configured to dynamically set adjacent access points to the channel.

Question 9
What are two differences between optical-fiber cabling and copper cabling? (Choose two.)

  • A: A BNC connector is used for fiber connections
  • B: The glass core component is encased in a cladding
  • C: The data can pass through the cladding
  • D: Light is transmitted through the core of the fiber
  • E: Fiber connects to physical interfaces using RJ-45 connections 

Question 10
How does CAPWAP communicate between an access point in local mode and a WLC?

  • A: The access point must not be connected to the wired network, as it would create a loop
  • B: The access point must be connected to the same switch as the WLC
  • C: The access point must directly connect to the WLC using a copper cable
  • D: The access point has the ability to link to any switch in the network, assuming connectivity to the WLC


You can buy ProfExam with a 20% discount..

Get Now!


Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen


Use VCE Exam Simulator to open VCE files