Free Download 200-150 Examp Dump: Introducing Cisco Data Center Networking.Testking.200-150.2019-07-22.1e.85q.vcex

Question 1

The network shown above is a flat network. SwitchF was recently added and powered up. Which of the following statements is true?

A: Initially, only broadcasts will be flooded by SwitchF
B: Initially, hosts directly connected to SwitchF will only be to communicate with each other
C: SwitchF will not transmit frames to SwitchE unitl SwitchF joins the VTP domain
D: Initially, all frames that SwitchF receives from SwitchE will be flooded

Correct Answer: D

Reference: https://www.cisco.com/c/en/us/support/docs/switches/catalyst-6000-series-switches/23563-143.html
https://www.cisco.com/c/en/us/support/docs/lan-switching/ethernet/12006-chapter22.html#trans

Question 2

Which of the following conditions would cause a Layer 2 switch to flood a received unicast frame out all ports except the port that received the frame? (Select two.)

A: The CAM table is full
B: The frame contains errors
C: The source MAC address in the frame is not in the switch’s CAM table
D: The destination MAC address in the frame is not in the switch’s CAM table

Correct Answer: AD

Reference: https://www.cisco.com/c/en/us/support/docs/switches/catalyst-6000-series-switches/23563-143.html
https://www.cisco.com/c/en/us/support/docs/lan-switching/ethernet/12006-chapter22.html#trans

Question 3

You need to adds a new router, two new switches, and several new computers to your company’s network. You need to determine which cables to use to connect the devices to the network.
Which of the following statements best describe how should connect cables to the devices? (Select three.)

A: Use a straight-through cable to connect the computers to the switches
B: Use a crossover cable to connect the computers to the switches
C: Use a crossover cable to connect one switch to the other switch
D: Use a straight-though cable to connect one switch to the other switch
E: Use a straight-through cable to connect a computer to the console port of the router
F: Use a rollover cable to connect a computer to the console port of the router

Correct Answer: ACF

Reference:
https://www.cisco.com/c/en/us/support/docs/lan-switching/ethernet/10561-3.html#appb
https://www.cisco.com/c/en/us/td/docs/security/asa/hw/maintenance/5585guide/5585Xhw/pinouts.pdf

Question 4

In which of the following situations should you use a crossover cable? (Select two.)

A: to connect the E0/0 interface of Router1 to the E0/0 interface of Router2
B: to connect the S0/0 interface of Router1 to the S0/0 interface of Router2
C: to connect the Fa0/0 interface of Router1 to the Fa0/0 interface of Switch1
D: to connect the serial port of Computer1 to the console port of Router1
E: to connect the Ethernet port of Computer1 to the Ethernet port of Computer2

Correct Answer: AE

Reference: https://www.cisco.com/c/en/us/support/docs/lan-switching/ethernet/10561-3.html#appb
https://www.cisco.com/c/en/us/td/docs/security/asa/hw/maintenance/5585guide/5585Xhw/pinouts.pdf

Question 5

Which of the following is a file-based storage protocol that is typically used on Microsoft Windows systems?

A: CIFS
B: FCoE
C: iSCSI
D: NFS

Correct Answer: A

Question 6

Which of the following RAID levels provides fault tolerance and requires a minimum of three disks?

A: RAID 0
B: RAID 1
C: RAID 5
D: RAID 1+0

Correct Answer: C

Question 7

You want to configure an edge port on a Nexus 7000 series switch so that it becomes error disabled when it receives a BPDU.
Which of the following commands should you issue from interface configuration mode?

A: spanning-tree bpdufilter enable
B: spanning-tree bpduguard enable
C: spanning-tree port type edge bpdufilter default
D: spanning-tree port type edge bpduguard default

Correct Answer: B

Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/nx-os/layer2/configuration/guide/b_Cisco_Nexus_7000_Series_NX-OS_Layer_2_Switching_Configuration_Guide/b_Cisco_Nexus_7000_Series_NX-OS_Layer_2_Switching_Configuration_Guide_chapter_01001.html

Question 8

You issue the spanning-tree bpduguard enable command from interface configuration mode on a Nexus 7000 series switch. Which of the following statements is true?

A: The specified port will ignore BPDUs
B: The specified port will accept BPDUs
C: The specified port will become error disabled when it receives a BPDU
D: All edge ports will be configured with BPDU Guard

Correct Answer: C

Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/nx-os/layer2/configuration/guide/b_Cisco_Nexus_7000_Series_NX-OS_Layer_2_Switching_Configuration_Guide/b_Cisco_Nexus_7000_Series_NX-OS_Layer_2_Switching_Configuration_Guide_chapter_01001.html

Question 9

You want to create an ACL on a Nexus switch that will permit only FTP traffic from 10.1.13.0/24 to 192.168.13.7.
Which of the following commands or command sets could you issue? (Select two.)

A:
B:
C:
D:
E:
F:

Correct Answer: CE

Reference:

https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus7000/sw/security/command/reference/n7k_sec_cmd/sec_cmd_i.html#pgfId-1245141
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus7000/sw/security/command/reference/n7k_sec_cmd/sec_cmd_d.html#pgfId-1230193
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus7000/sw/security/command/reference/n7k_sec_cmd/sec_cmd_k_to_p.html#pgfId-1244275

Question 10

You want to create an ACL on a Nexus switch that will deny only unencrypted web traffic from 192.168.99.0/24 to any destination.
Which of the following command sets could you issue? (Select two.)

A:
B:
C:
D:
E:

Correct Answer: CD

Reference:

https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus7000/sw/security/command/reference/n7k_sec_cmd/sec_cmd_i.html#pgfId-1245141
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus7000/sw/security/command/reference/n7k_sec_cmd/sec_cmd_d.html#pgfId-1230193
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus7000/sw/security/command/reference/n7k_sec_cmd/sec_cmd_k_to_p.html#pgfId-1244275

Exam	Introducing Cisco Data Center Networking
Number	200-150
File Name	Introducing Cisco Data Center Networking.Testking.200-150.2019-07-22.1e.85q.vcex
Size	7.9 Mb
Posted	July 22, 2019
Downloads	27

Download Introducing Cisco Data Center Networking.Testking.200-150.2019-07-22.1e.85q.vcex

File Info

How to open VCEX & EXAM Files?

Demo Questions

PROFEXAM WITH A 20% DISCOUNT