Download CCNA Cisco Certified Network Associate CCNA (v3-0).CertDumps.200-125.2020-06-01.1e.1123q.vcex
Download Exam
File Info
| Exam | CCNA Cisco Certified Network Associate CCNA (v3.0) |
| Number | 200-125 |
| File Name | CCNA Cisco Certified Network Associate CCNA (v3-0).CertDumps.200-125.2020-06-01.1e.1123q.vcex |
| Size | 57 Mb |
| Posted | June 01, 2020 |
| Downloads | 315 |
How to open VCEX & EXAM Files?
Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.
Coupon: EXAMFILESCOM
With discount: 20%
Demo Questions
Question 1
In which two formats can the IPv6 address fd15:0db8:0000:0000:0700:0003:400F:572B be written? (Choose two.)
- A: fd15:0db8:0000:0000:700:3:400F:527B
- B: fd15::db8::700:3:400F:527B
- C: fd15:db8:0::700:3:4F:527B
- D: fd15:0db8::7:3:4F:527B
- E: fd15:db8::700:3:400F:572B
Question 2
What are three characteristics of the TCP protocol? (Choose three.)
- A: It uses a single SYN-ACK message to establish a connection.
- B: The connection is established before data is transmitted.
- C: It ensures that all data is transmitted and received by the remote device.
- D: It supports significantly higher transmission speeds than UDP.
- E: It requires applications to determine when data packets must be retransmitted.
- F: It uses separate SYN and ACK messages to establish a connection.
Question 3
Drag and drop the Ethernet terms from the left onto the correct descriptions on the right.
Question 4
Refer to the exhibit.
All of the routers in the network are configured with the ip subnet-zero command. Which network addresses should be used for Link A and Network A? (Choose two.)
All of the routers in the network are configured with the ip subnet-zero command. Which network addresses should be used for Link A and Network A? (Choose two.)
- A: Link A – 172.16.3.0/30
- B: Link A – 172.16.3.112/30
- C: Network A – 172.16.3.48/26
- D: Network A – 172.16.3.128/25
- E: Link A – 172.16.3.40/30
- F: Network A – 172.16.3.192/26
Question 5
Which type of device can be replaced by the use of subinterfaces for VLAN routing?
- A: Layer 2 bridge
- B: Layer 2 switch
- C: Layer 3 switch
- D: router
Question 6
What are two benefits of private IPv4 IP addresses? (Choose two.)
- A: They are routed to the Internet the same as public IP addresses.
- B: They are less costly than public IP addresses.
- C: They can be assigned to devices without Internet connections.
- D: They eliminate the necessity for NAT policies.
- E: They eliminate duplicate IP conflicts.
Question 7
Which two server types are used to support DNS lookup? (Choose two.)
- A: web server
- B: ESX host
- C: authoritative name server
- D: file transfer server
- E: name resolver
Question 8
Which three statements about IPv6 prefixes are true? (Choose three.)
- A: FEC0::/10 is used for IPv6 broadcast.
- B: FC00::/7 is used in private networks.
- C: FE80::/8 is used for link-local unicast.
- D: FE80::/10 is used for link-local unicast.
- E: 2001::1/127 is used for loopback addresses.
- F: FF00::/8 is used for IPv6 multicast.
Question 9
Refer to the exhibit.
The network administrator cannot connect to Switch 1 over a Telnet session, although the hosts attached to Switch1 can ping the interface Fa0/0 of the router. Given the information in the graphic and assuming that the router and Switch2 are configured properly, which of the following commands should be issued on Switch1 to correct this problem?
The network administrator cannot connect to Switch 1 over a Telnet session, although the hosts attached to Switch1 can ping the interface Fa0/0 of the router. Given the information in the graphic and assuming that the router and Switch2 are configured properly, which of the following commands should be issued on Switch1 to correct this problem?
- A: Switch1(config)# ip default-gateway 192.168.24.1
- B: Switch1(config)# interface fa0/1
Switch1(config-if)# switchport mode trunk - C: Switch1(config)# line con0
Switch1(config-line)# password cisco
Switch1(config-line)# login - D: Switch1(config)# interface fa0/1
Switch1(config-if)# ip address 192.168.24.3 255.255.255.0 - E: Switch1(config)# interface fa0/1
Switch1(config-if)# duplex full
Switch1(confiq-if)# speed 100
Question 10
Which two statements about IPv6 and routing protocols are true? (Choose two.)
- A: EIGRPv3 was developed to support IPv6 routing.
- B: OSPFv3 was developed to support IPv6 routing.
- C: Loopback addresses are used to form routing adjacencies.
- D: EIGRP, OSPF, and BGP are the only routing protocols that support IPv6.
- E: Link-local addresses are used to form routing adjacencies.
HOW TO OPEN VCEX AND EXAM FILES
Use ProfExam Simulator to open VCEX and EXAM files
HOW TO OPEN VCE FILES
Use VCE Exam Simulator to open VCE files
